SaltDogg SHPE Controller (3014199) - SHPE0750, SHPE1500, SHPE2000, SHPE4000 - Manual (Page 2)

2
TM
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • saltdogg.com
3019470 Rev. C
WARRANTY
Buyers Products Co. warrants all truck/trailer hardware manufactured or distributed by it, to be free from defects in material and
workmanship for a period of one year from date of shipment. Parts must be properly installed and used under normal conditions.
Any product which has been altered, including modification, misuse, accident or lack of maintenance will not be considered under
warranty. Normal wear is excluded. The sole responsibility of Buyers Products Co. under this warranty is limited to repairing or replacing any part
or parts which are returned, prepaid, and are found to be defective by Buyers Products Co. Authorization from Buyers Products Co. must be obtained
before returning any part. No charges for transportation or labor performed on Buyers’ products will be allowed under this warranty.
1. To start spreader, be sure that truck engine is running to prevent battery from discharging. Flip power switch to ON
position. Controller switches will illuminate. Auger and spinner motors will start with full speed for a short time (displays
will show 9) and then drop to the speed settings selected.
2. To adjust speed simply rotate speed knobs until desired speed number is achieved.
3. To activate vibrator flip the Vibrator switch to ON position. Vibrator switch will illuminate. To turn vibrator OFF flip switch
to OFF position.
4. To turn controller OFF, simply flip power switch to OFF position.
5. If battery voltage drops below 10 VDC, controller shuts off automatically.
Controller Codes
AUGER DISPLAY
SPINNER
DISPLAY
MOTOR, WIRE HARNESS,
CONTROLLER STATUS
ACTION REQUIRED
1 blinking blinking
Ignition wire connected to 12 VDC source,
positive wire is not connected to battery
Connect positive wire to battery
2 F
Positive motor wire in wire harness shorted
to trucks body/frame.
Internal fuse 40 AMP blown.
Find and eliminate short circuit.
Replace fuse.
3 F
Positive motor wire in wire harness shorted
to trucks body/frame.
Internal fuse 40 AMP blown.
Find and eliminate short circuit.
Replace fuse.
4 U F
Short circuit between vibrator wires and
trucks body/frame.
Short circuit between vibrator wires.
External 30 AMP fuse is blown.
Internal fuse 40 AMP blown.
Find and eliminate short circuit.
Replace vibrator.
Replace fuse.
5 A Missing connection in Auger circuit. Find and eliminate missing connection.
6 P Missing connection in Spinner circuit. Find and eliminate missing connection.
7
Speed number is blinking.
Auger motor is alternating
forward/ reverse rotations.
Auger jammed, auger motor overloaded.
Clear jam in auger trough.
Adjust hopper baffles to reduce auger load.
8
Speed number
is blinking.
Spinner motor overloaded.
Reduce amount of material falling on spinner
disc. Clear spinner disk before starting
spreader.
9 U Missing connection in vibrator circuit. Find and eliminate missing connection.
10 L Low battery voltage. Check trucks electrical system.
11 C Controller temperature is higher than 160F Relocate controller to have better cooling.
12 H
Auger motor wires in wire harness shorted to
each other. Short location close to controller.
Find and eliminate short circuit.
13 H
Spinner motor wires in wire harness shorted
to each other. Short location close to
controller.
Find and eliminate short circuit.
14
Speed number is blinking,
motor stopped. Auger motor wires in wire harness shorted to
each other. Short location close to motor.
Find and eliminate short circuit.
15
Speed number
is blinking,
motor stopped.
Spinner motor wires in wire harness shorted
to each other. Short location close to motor.
Find and eliminate short circuit.
F F