Robertshaw 9500 - Manual

Features
• Single Stage heat pump compatible
• Zone system compatible as a master thermostat
• Low battery indicator.
• Fahrenheit/Celsius display option.
• Adjustable from 45(F (4°C) to 90°F (32(C).
• Accuracy within ± 1 degree.
• Adjustable temperature differential: .5 – 1.5 degree.
• Low temperature freeze protection. While in heat mode, thermostat
will mechanically turn on heat if temperature drops to 40°F (4°C) -
even if batteries are missing or drained.
• Automatic heating shutdown if temperature exceeds 90°F (32°C).
Replacing Existing Thermostat
1. Turn off power to heating and cooling system.
2. Remove cover of old thermostat to expose wires.
Do not disconnect wires. (Fig. 1)
3. Label wires per Table 1.
Table 1
Old Label New Label Description
M, 4, RH, R5 or R RH Heat Transformer,
hot side
V or RC RC Cooling Transformer,
hot side
Y or Y6 Y Cooling control
H, W or 4 W Heating control
F or G G Fan control relay
C* Y or None Either cooling control
or common side
of transformer
O O Cool Active Reversing
Valve
B B Heat Active Reversing
Valve
*NOTE: O N SOME OLDER MODELS , THE C TERMINAL CAN BE EITHER THE COOLING CONTROL OR THE
COMMON SIDE OF THE TRANSFORMER . C HECK FURNACE WIRING DIAGRAM TO VERIFY C TERMINAL . I F IT
IS THE COMMON SIDE OF THE TRANSFORMER , CAP THE WIRE AND TUCK INTO THE WALL . I F IT IS THE
COOLING CONTROL , CONNECT TO THE Y TERMINAL .
4. After labeling wires, remove wires from terminals.
5. Remove existing thermostat base from wall.
6. Refer to the following section for instructions on how to
install thermostat.
Installing Model 9500 Thermostat
NOTE: F OR NEW INSTALLATIONS , MOUNT THERMOSTAT ON INSIDE WALL , 4-5 FEET ABOVE THE FLOOR .
D O NOT INSTALL BEHIND A DOOR , IN A CORNER , NEAR AIR VENTS , IN DIRECT SUNLIGHT , OR NEAR ANY
HEAT OR STEAM GENERATING FIXTURES . I NSTALLATION AT THESE PLACES WILL AFFECT THERMOSTAT
OPERATION .
1. Turn power off to the heating
and cooling systems.
2. Place COOL-OFF-HEAT
In OFF position.
3. Place AUTO-ON switch
Into AUTO position.
4. Remove the cover using a coin
or screwdriver.
5. Place thermostat against the wall at desired location. Make sure
wires will feed through opening on base of thermostat.
6. Mark placement of mounting holes. See Fig. 3.
Set base aside.
7. Drill the marked holes using a 3/16" drill bit. NOTE: Enclosed plastic
anchors do not require drilled hole for drywall.
8. Tap plastic anchors into the wall.
9. Align base with plastic anchors and feed wires
through opening.
10. Secure base to wall with supplied screws.
11. Connect wires to terminal strip. Refer to wiring diagrams on other
side of this sheet. Make sure wire connections are secure.
12. Place fan option switch into either the "ELEC" or "GAS" position
depending upon the type of furnace. Refer to Figure 4
figure 4
13. Put the °F/°C switch to either °F for Fahrenheit display
or °C for Celsius display readout.
14. Put the HP/NON HP switch to either the HP for Heat Pump or NON
HP for furnace applications in the proper position.
15. Install two “AA” ENERGIZER brand batteries or equivalent into bat-
tery compartment. Be sure to match positive (+) ends of batteries
with positive (+) battery terminals in the battery compartment. The
display will show as follows:
16. Replace cover onto thermostat by snapping into place.
17. Turn on power to system . Test thermostat as described in
the following section.
To Test Thermostat
WARNING: DO NOT SHORT (JUMPER) ACROSS TERMINALS OF GAS VALVE OR SYS-
TEM CONTROL TO TEST OPERATION. THIS WILL DAMAGE THE THERMOSTAT AND
VOID YOUR WARRANTY.
CAUTION: D O NOT SWITCH SYSTEM TO COOL IF THE TEMPERATURE IS BELOW 50°F (10°C). T HIS
CAN DAMAGE THE AIR CONDITIONING SYSTEM AND CAUSE PERSONAL INJURY .
1. Place the COOL-OFF-HEAT switch
into the COOL position
2. Press the button until the
temperature setting is at least
3 degrees below the room temperature.
The air conditioning system should
turn on within a few seconds.
NOTE: When in the COOL mode (or HEAT and COOL for single stage heat
pumps), once the thermostat turns off, a built in 5-minute delay prevents
the system from turning on again. This protects the compressor. No addi-
tional time delay relay is required. To override the 5-minute delay for
installation, press the reset button.
3. Put the COOL-OFF-HEAT switch
into the OFF position. The air
conditioning system should turn off.
4. Put the COOL-OFF-HEAT switch
into the HEAT position.
5. Press the button until the
temperature setting is at least
3 degrees above room temperature.
The heating system should turn on.
The fan may not turn on immediately,
depending upon the fan delay built
into the furnace.
6. Put the COOL-OFF-HEAT switch
into the OFF position. The heating
system should turn off. The fan may
continue to run for a short period
of time .
7. Put the AUTO-ON switch to
the ON position. The blower fan
should turn on.
8. Put the AUTO-ON switch to
the AUTO position. The blower fan
should turn off.
IMPORTANT SAFETY INFORMATION
WARNING:
• Always turn off power at the main power source by unscrewing
fuse or switching circuit breaker to the off position before installing,
removing, cleaning or servicing thermostat.
• Read all of the information in this manual before installing or pro-
gramming this thermostat
• This is a 24V AC low-voltage thermostat. Do not install on voltages
higher than 30V AC.
• All wiring must conform to local and national building and electrical
codes and ordinances.
• Do not short (jumper) across terminals on the gas valve or at the
system control to test installation. This will damage the thermostat
and void the warranty.
1 2 3 4 5 6
>
COOL OFF HEAT AUTO - ON > >
COOL OFF HEAT
AUTO - ON
Figure 1
Figure 2
MOUNTING HOLES
ELECTRIC/
GAS SWITCH
F ° / ° C
Switch
COOL OFF HEAT
COOL OFF HEAT
COOL OFF HEAT
COOL OFF HEAT
AUTO - ON
AUTO - ON
>
HP/NON HP
Switch
1 Heat / 1 Cool
W
A R R A N T Y
I N T E G R A T E D C O M F O R T S O L U T I O N S ™
DIGITAL
NON-PROGRAMMABLE
THERMOSTAT
9500
User’s Manual
Quick Start
Installation and
Programming
110-734
®
ELECTRIC
E
GAS
G
110-734B