Rivers Edge RE634 2 MAN - Manual (Page 12)

Check for parts online at www.huntriversedge.com or call 800-450-EDGE (3343) M-F 8-5 12
Operator's Manual
Rivers Edge® Two-Man Ladder Stands
8. Attach the backrest rim (10325) to the side seat support loops using
(4) provided 1/4-20 x 2-1/4” bolts, locknuts and steel washers. SEE
fIGuRE 5. You must now tighten all nut and bolt assemblies. Be
sure not to over tighten or crush tubing when tightening!
9. With all nut/bolt assemblies tightened, flip the seat assembly to the
upright position. This must be done in order to allow slack in the mesh
material to complete seat attachment. Attach the mesh backrest and (1)
retainer bar (10239) to the top side of backrest rim using (7) provided 1/4-
20 x 1-1/2” bolts and locknuts. SEE fIGuRES 6A/6B. The mesh backrest
must wrap around top side of backrest tube and the plastic stiffening
rod located in the sewn sleeve of mesh backrest MUST be positioned
behind the retainer bar to act as a stop and prevent the backrest from
pulling out during use. All bolts MUST go through the retainer bar, holes
provided in mesh backrest and the backrest rim. Tighten these bolts
securely at this time. Do not crush tubing when tightening.
10. With the seat still flipped up into the upright position (to allow for
slack in mesh material), attach the mesh “tail” section of the seat/
backrest and (1) retainer bar (10239) to the top side of tree blade
frame using (7) provided 1/4-20 x 1-1/2” bolts and locknuts. SEE
fIGuRES 6A/6B. The mesh “tail” section must be positioned on top
side of tree blade tube and the plastic stiffening rod located in the
sewn sleeve of mesh “tail” section MUST be positioned behind the
retainer bar to act as a stop and prevent the “tail” section from pulling
out during use. All bolts MUST go through the retainer bar, holes
provided in mesh “tail” section and the tree blade. Tighten these
bolts securely at this time. Do not crush tubing when tightening.
11. a. Attach the two shooting rail stop mounts (10328) to the side seat
support loops using (2) provided 1/4-20 x 1-1/2” bolts and locknuts.
SEE fIGuRE 7. Be sure that each mount is oriented to the outside
of each side seat support loop.
b. Press (2) provided rubber bumper stops (48679) into the top side
hole of each stop mount. SEE fIGuRE 7.
12. Attach the two shooting rail receiver tubes (10326) to the outside of
each side seat support loop using (2) provided 1/4-20 x 2-3/4” bolts,
locknuts, steel washers and nylon spacers. SEE fIGuRE 7.
13. Insert the shooting rail rim (10327) into the shooting rail receiver
tubes and secure together using (2) provided 1/4-20 x 1-1/2” bolts,
locknuts and steel washers. SEE fIGuRE 7. You must now tighten
all nut and bolt assemblies. Be sure not to over tighten or crush
tubing when tightening!
Figure 6A
64212
Figure 7 Figure 5
1/4-20 X 2-1/4" bolts
steel washers
backrest rim
locknuts
1/4-20 X
2-1/4" bolts
steel
washers
mesh backrest
retainer bar
1/4-20 X 1-1/2" bolts
locknuts
retainer bar
1/4-20 X
1-1/2" bolts
locknuts
shooting rail rim
locknuts
shooting rail stop mounts 1/4-20 X 1-1/2" bolts
locknuts
1/4-20 X
1-1/2" bolts
bumper stops
shooting rail receiver tubes
steel washers
1/4-20 X
2-3/4" bolts
steel
washers
nylon spacers
1/4-20 X
1-1/2" bolts
steel washers
1/4-20 X 2-3/4" bolts
Figure 6B: side view
1/4-20 X 1-1/2" bolts
retainer bar
mesh backrest
mesh seat
retainer bar
1/4-20 X 1-1/2" bolts
locknuts
stiffening rod