Rivers Edge RE634 2 MAN - Manual (Page 11)

Check for parts online at www.huntriversedge.com or call 800-450-EDGE (3343) M-F 8-5 11
Operator's Manual
Rivers Edge® Two-Man Ladder Stands
ASSEMBlY INSTRuCTIONS (RE633)
Tools needed – two 7/16” wrenches
IMpoRTanT asseMBlY TIp: do noT TIGHTen nuT & BolT coMBInaTIons
coMpleTelY unTIl all paRTs aRe asseMBled ToGeTHeR! FInGeR TIGHTen
onlY plus one TuRn oF a wRencH onlY! THIs wIll TeMpoRaRIlY Hold
THe locK nuT on THe BolT wHIle HelpInG alIGnMenT oF all paRTs!
aFTeR all paRTs aRe asseMBled ToGeTHeR.
Tools needed – two 7/16” wrenches
1. Attach the two foot platforms (2ML133) together using (2) provided
1/4-20 x 2-1/4” bolts, locknuts and steel washers. SEE fIGuRE 1. DO
NOT tighten all nut and bolt assemblies completely!
2. Attach the two platform J-pipes (10321) to the assembled platforms
using (4) provided 1/4-20 x 2-1/2” bolts, locknuts and steel washers.
SEE fIGuRE 2.
noTe: Mesh surface of foot platforms should be on top.
3. Attach the tree blade (2ML130) to the platform J-pipes using (2) provided
1/4-20 x 2-1/2” bolts, locknuts and steel washers. SEE fIGuRE 2.
4. Attach the two side seat support loops (10322) to the rear platform
using (4) provided 1/4-20 x 2-1/4” bolts, locknuts and steel washers.
SEE fIGuRE 3.
5. Attach the two ladder platform braces (LL9A) to the side seat support
loops and rear platform using (4) provided 1/4-20 x 1-1/2” bolts and
locknuts. SEE fIGuRE 3.
6. a. Attach the upper, large tree blade frame (10323) to the inside
of side seat support loops using (4) provided 1/4-20 x 2-3/4” bolts,
locknuts, steel washers and nylon spacers. SEE fIGuRE 4. Blade
should be on bottom side, towards platform.
b. Press (2) provided rubber bumper stops (48679) into the top side
holes of tree blade frame. SEE fIGuRE 4. Blade should be on bottom
side, towards the platform.
7. Attach the seat frame assembly (10332) to the inside of side seat
support loops using (2) provided 1/4-20 x 2-3/4” bolts, locknuts,
steel washers and nylon spacers. SEE fIGuRE 4.
noTe: The mesh seat is not shown in FIGuRe 4 for ease of assembly
view although it is already factory assembled to the metal seat
frame. Make sure the metal seat frame is oriented onto the ladder
assembly correctly with the “channel” portion facing downward,
towards the foot platform. Mesh seat/backrest should temporarily
lay on top of seat until its assembly later in assembly instructions.
Figure 1
Figure 2
Figure 3
Figure 4
1/4-20 X
2-1/4" bolts
locknuts
steel washers
1/4-20 X 2-1/2" bolts
foot platforms
platform
J-pipes
tree blade
locknuts
steel washers
1/4-20 X 2-1/2" bolts
steel washers
locknuts
1/4-20 X
2-1/4" bolts
seat support
loops
steel
washers
1/4-20 X
1-1/2" bolts
1/4-20 X 1-1/2" bolts
platform braces
locknuts
locknuts
1/4-20 X
2-3/4" bolts
steel washers upper tree
blade frame
1/4-20 X 2-3/4" bolts
nylon spacers
locknuts
bumper
stops
seat frame assembly
1/4-20 X
2-3/4" bolts steel washers
nylon spacers
1/4-20 X 2-3/4" bolts