Rivers Edge RE627 Oasis - Manual (Page 36)

Check for parts online at www.huntriversedge.com or call 800-450-EDGE (3343) M-F 8-5 Check for parts online at www.huntriversedge.com or call 800-450-EDGE (3343) M-F 8-5 36
Operator's Manual
Rivers Edge® One-Man Ladder Stands
3. With two people securely holding the ladder, use the three point
contact climbing method to slowly climb the ladder and carefully
keep a constant hand grip on the ladder at all times. Always lean
forward, toward tree, to keep top section tree blades against the
tree. Be certain ladder bottom is firmly seated on dry, level
ground. Attach your harness tether to the tree before securing
the platform to the tree and stepping onto platform. Refer to
the full Body harness instructions included with this product.
4. Standing on ladder step, lean toward tree with ratchet strap now in
hand, hook "S" hook with long strap through hole provided on tree
blade. Feed the long strap through the center (slot) of ratcheting
mechanism and back around through tightening lever. sEE fIGuREs
2 and 3.
notE: Be sure you feed the long strap correctly so there are no
twists in the strap.
Wrap entire ratchet assembly around tree and hook other "S" hook
through opposite tree blade hole. Pull tail of long strap until most
of the slack is taken out. Be sure entire strap is even and at the same
level all around tree. "Ratchet" tight to tree, this will securely attach
ladder to tree and prevent movement. sEE fIGuREs 2 and 4.
notE: to release ratchet, simply pull the release lever and open
tightening lever wide open (flat).
5. If applicable, attach backrest portion of seat to tree by wrapping the
long strap with buckle end around tree and snapping together with
opposite end. Adjust as needed.
6. If applicable, once seated the shooting rail can now be seated down
over studs of armrest mounts. sEE fINIshED lADDER IMAGEs.
7. Reverse setup and use instructions to take ladder down.
Figure 2
pull tail to take out slack
tightening lever
release lever
feed through slot
TREE
ratchet
back and
forth
Figure 3
Figure 4
WARNING
BE CERTAIN TO AlWAYs lEAN fORWARD, TOWARD ThE TREE
WhEN AsCENDING OR DEsCENDING lADDER. ATTACh YOuR
hARNEss TEThER TO ThE TREE BEfORE sECuRING ThE PlAT-
fORM TO ThE TREE AND sTEPPING ONTO ThE PlATfORM.
AlWAYs hAvE ThREE POINTs Of CONTACT WhIlE ClIMBING
lADDER.
BRING RATChET sTRAP(s) uP WITh YOu IN A POCkET- DO
NOT CARRY IN YOuR hANDs!
DO NOT AllOW EXCEssIvE sTRAP BuIlDuP IN RATChET As
ThIs WIll PREvENT ThE RATChET TEETh fROM ENGAGING
CAusING slIPPAGE.
AlWAYs ATTACh RATChET sTRAPs sECuRElY WhIlE usING
ThIs PRODuCT!
NEvER sTAND ON lADDER sEAT, IT Is DEsIGNED fOR sIT-
TING ONlY.
sEAT Is REMOvABlE. BE CERTAIN IT Is sECuRElY ATTAChED
WhEN IN usE.
BE suRE shOOTING RAIl Is sEATED All ThE WAY DOWN ON
sTuDs DuRING usE.
NEvER lEAN AGAINsT, lEAN OvER, OR sIT ON shOOTING
RAIl. IT Is DEsIGNED As A shOOTING REsT ONlY. AlWAYs
BE AWARE ThAT ThE shOOTING RAIl CAN sWING TO ONE
sIDE OR ThE OThER.
BE suRE shOOTING RAIl Is sET Off TO ThE sIDE (ON ONE
sTuD) WhEN AsCENDING OR DEsCENDING lADDER.