Alliance Laundry Systems F232157R7 - Manual (Page 29)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming
27 F232157
Drain Error (For Models With Firmware ID
Code “C2dS” and “CvdS”)
If machine has not drained within 4 minutes 15
seconds, display flashes “Erdn”, time remaining, and
buzzer beeps. The buzzer stops beeping after 30
seconds while display flashes “Erdn” until machine
empties. If machine empties, ending Drain Error
condition, display stops flashing, buzzer turns off, and
remaining cycle time displays as the cycle resumes.
If machine does not empty, display continues flashing
“Erdn”. The drain error counter increases by one.
Refer to Cycle and Error Count section.
Clogged Filter (All C80 and C60 X Voltage
ONLY Models)
A clogged filter can cause the inverter drive to run at
an elevated temperature. If the control senses an
elevated inverter drive temperature, the bottom
indicator LED on front panel decal lights. Check and
clean the drive compartment filter if necessary. The
light turns off AFTER one cycle runs at normal
temperature.
Door Will Not Unlock
If the door solenoid cannot retract (unlocking the door)
at the end of the stop routine, the display will show
“----” for ten seconds. In all models except an early
version of the 125, control attempts to unlock the door
again by pulsing the door solenoid every ten seconds
for a total of five times. An early version of the 125
model has a door unlock button.
The display then flashes “CAnt”/“OPEn”, indicating it
cannot unlock the door. This indicates a problem, and
a qualified service technician should be consulted.
At the end of a cycle or at power up, before the control
will allow the door to unlock, control checks for low,
medium or high water level. Control allows the door to
unlock only when machine is empty. If any water level
is indicated, display shows “FULL” while keeping all
outputs off. This condition could indicate a slow drain
system or a mechanical blockage of the drain. Contact
an authorized service person, mentioning display on
control.
On Board Battery Problem
If certain functions require the on board battery
(dependent on specific machines) and if battery charge
is low, or battery is removed, the control will display
“bAtt”. This is displayed several seconds after power
is applied to the control. Contact an authorized service
person if condition continues.
Temperature Probe Malfunction
If display shows “+SFL”, “-19C”, or “00F”, the
temperature probe may need to be replaced. If problem
persists after changing probe, contact an authorized
service person.
Rapid Advance (For Models With
Firmware ID Code “C2dS” and
“CvdS”)
Enabling Rapid Advance
NOTE: Rapid Advance can only be used during a
cycle operation.
To enable Rapid Advance while a cycle is in progress,
machine must be in PROGRAM Mode. Refer to
Entering Program Mode.
How to Rapid Advance During All Steps
(Except First Fill Step)
1. Make sure Rapid Advance is enabled.
2. Enter PROGRAM Mode. Refer to Entering
Program Mode.
3. Press the Advance ( ∧) keypad to advance to
desired step.
4. Display will show recalculated time remaining.
How to Rapid Advance (During First Fill
Step)
1. Make sure Rapid Advance is enabled.
2. While machine is filling with water, enter
PROGRAM Mode. Refer to Entering Program
Mode.
3. To advance to the next step, press START
(Enter) keypad to turn off the ability to change
cycles.
4. Press the Advance ( ∧) keypad to advance to
desired step.
5. Display will show recalculated time remaining.
NOTE: If control is set up for ‘Eti
n
’, the remaining
cycle time after using Rapid Advance step is
calculated as if control was configured for ‘Pti
n
’.
This is because any time estimations following
advance would be inaccurate. After the cycle ends,
and the ADVANCE Mode is disabled, the next cycle
display remaining cycle time based on the ‘Eti
n
’
configuration.