ADTRAN 1xN User Manual
Page 3
3
61190860L1-5B
Section 61190860L1-5, Issue 2
Documentation associated with the listed cards
provides information on implementing the auto-protect
function.
LED Indication
Table 1 describes LED indication.
• All LEDs OFF indicates no power to the SCIM.
• All LEDs flashing red indicates the protect card is
disabled and SCIM power is local -48 VDC.
2. INSTALLATION
After unpacking the unit inspect it for damage. If
damage is noted, file a claim with the carrier then
notify ADTRAN. Refer to Warranty and Customer
Service.
Mounting Procedure
The 1xN Pro-Cap installs at the remote location using
the following procedure:
NOTE
All component fasteners are spring-loaded,
captured thumb screws.
1. Remove the housing from the shelf by unscrewing
the two thumb screws on the side of the housing.
The housing pulls out and away from the shelf.
2. Remove the shelf from the mounting-plate by
unscrewing the thumb screw at the top center of
the shelf bay. It is not necessary to remove the
SCIM assembly unless its position is to be
reversed to the other side of the shelf.
3. The shelf assembly lifts away from the mounting-
plate by disengaging the chassis tabs from the
mounting-plate support hooks.
4. Using the mounting-plate as a template, position
the mounting-plate at the desired location and
mark four pilot holes. Ensure the unit is level and
that cable plugs will reach their designated
sockets.
5. Using an appropriate bit, drill the four pilot holes.
6. Align the mounting-plate to the pilot holes and
attach to the wall with appropriate fasteners.
7. Reassemble the unit by reversing steps
1 through 3.
Cable Connections
Frame Ground
Both the shelf and SCIM have separate ground
connections. Each must be connected to a known
approved ground location. Verify metal to metal
contact on all connections and ensure ground circuit
continuity.
The shelf has various openings for wire route options
along with tie-wrap anchor points and extrusions for
securing cables and connectors.
Specific wiring arrangements are customer developed.
CAUTION
Transmit and receive loops to both facility and
CPE have two connection schemes. Only one
connection method is to be used, not both.
Facility Side
Amphenol Connection – The to-facility and
from-facility amphenols can be either left-side or
right-side oriented.
C A U T I O N
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
Table 1. LED Indication
D
E
L
t
o
l
S
F
F
O
n
e
e
r
G
h
s
a
l
F
n
e
e
r
G
d
i
l
o
S
d
e
R
h
s
a
l
F
d
e
R
d
i
l
o
S
n
e
e
r
G
/
d
e
R
h
s
a
l
F
7
-
1
t
c
e
t
o
r
P
d
e
t
c
e
l
e
s
e
D
o
t
t
s
e
u
q
e
R
e
l
b
a
n
E
t
c
e
t
o
r
P
t
c
e
t
o
r
P
d
e
l
b
a
n
E
d
r
a
C
t
c
e
t
o
r
P
*
*
d
e
l
b
a
s
i
D
t
c
e
t
o
r
P
n
I
*
e
d
o
M
A
/
N
T
O
R
P
8
k
r
o
w
t
e
N
o
N
l
a
n
g
i
S
t
c
e
t
o
r
P
d
e
t
a
v
i
t
c
A
n
I
t
c
e
t
o
r
P
y
b
d
n
a
t
S
d
r
a
C
t
c
e
t
o
r
P
*
*
d
e
l
b
a
s
i
D
A
/
N
d
e
m
r
A
d
r
a
C
t
c
e
t
o
r
P
L
I
A
F
t
c
e
t
o
r
P
l
a
n
o
i
t
a
r
e
p
O
A
/
N
A
/
N
d
r
a
C
t
c
e
t
o
r
P
*
*
d
e
l
b
a
s
i
D
e
r
u
l
i
a
F
t
c
e
t
o
r
P
A
/
N
.
e
d
o
M
t
c
e
t
o
r
P
n
i
e
b
n
a
c
7
h
g
u
o
r
h
t
1
s
t
o
l
s
n
i
e
m
i
t
a
t
a
e
l
u
d
o
m
e
n
o
y
l
n
O
*
.
F
F
O
3
S
h
c
t
i
w
s
t
c
e
t
o
r
P
*
*