Earthway 6500W Kentucky Style High Wheel Cultivator User Manual
Earthway, Kentucky, 6500w

ASSEMBLY OF THE 6500W
Remove and identify all loose parts from carton
I. Install handle bracket (20) to inside of wood handles (24). NOTE: Slight bend in handle bracket
(20) to face outward and that you need to mount them so they face each other, see below right.
II. Insert 5/16-18 x 1½” bolts (8) through holes in wood handles then through holes in handle bracket, fasten using 5/16-18 hex nut (12).
III. Insert axle bolt (11) through hole in handle bracket (20). Now insert the bolt through hole in the straight end of frame (1). Place
axle (2) into center of wheel (21). Now put axle bolt (11) through the axle (2), then put other frame (1) and other handle bracket (20)
over axle bolt and fasten with 5/16 lock washer (14) and 5/16 hex nut (12).
IV. Insert 5/16-18 x 1¼” bolt (7) through hole in bottom of right tool support (6). Now put spacer (4) onto bolt (7)and install left tool
support (5) and fasten with 5/16 hex nut (12).
V. Put tool support assembly from Step IV above between frame (1) ends with spacer end down and curve toward
wheel. Next fasten the frame (1) to tool support assembly with ¼-20 x 2” bolt (9) and ¼-20 locknut (13).
VI. NOTE: Four holes in (5 & 6) are for adjustable height for easier operating. Now take wood handles (24) and
attach to tool support supports (5 & 6) using 5/16-18 x 1½” bolt (8) and 5/16 hex nut (12).
VII. Now install cross brace (3) to wooden handles using #14 x 1¼” screws (10).
30
28
13
31
27
Slicing Hoe #60132
29
18
16
15
17
15
17
16
23
22
12
7
15
16
17
Furrow Plow
#44227
Hilling/Mold Board
Plow #44228
Five Tine
Cultivator
#60141
19
12
20
14
(2) 31129
#14 x 1-1/4”
Screw
(9) 32102
5/16”-18
Hex Nut
32109
3/8”-16
Hex Nut
32103
1/4”-20
Lock Nut
43033
Formed
Washer
34104
5/16” Lock
Washer
23500
Axle
23605
Tool Support
Spacer
(3) 31111
5/16-18 x 1¼”
Bolt
31101
1/4-20 x 3/4”
Bolt
Optional
(6) 31115
5/16-18 x 1-1/2”
Bolt
31120
1/4-20 x 2”
Bolt
37105
3/8-16 x 2”
Carriage Bolt
31131
5/16-18 x 5”
Bolt
ASSEMBLY OF TOOLS
(see above right)
FURROW PLOW
Place Furrow Plow in front of tool support slot. Put carriage bolt (16) through square hole and through slot in tool support. Next put formed
washer (17) over carriage bolt (16) and tool support: fasten with lock nut (15) and tighten fully.
HILLING / MOLD BOARD PLOW
Place Hilling Plow in position shown above. Put carriage bolt (16) through square hole and through slot in tool support. Next put formed
washer (17) over carriage bolt (16) and tool support: fasten with lock nut (15) and tighten fully.
FIVE TINE
Assemble Fine Tine as pictured above. Fasten with two bolts (7) and two (12) hex nuts, tighten fully. Next put carriage bolt (16) through rear
of the Five Tine Assembly and through tool support, fasten with formed washer (17) and lock nut (15).
EarthWay
R
6500W
KENTUCKY
HIGH-WHEEL CULTIVATOR
ASSEMBLY INSTRUCTIONS
Congratulations on the purchase of this new Earthway High-Wheel Cultivator. Please contact us if you have any difficulty with assembly
or operation of this product. We can be reached via the telephone at 800-294-0671 or 574-848-7491 Monday - Friday 9:00am ~ 4:00pm or
visit us online at www.earthway.com The 6500W comes with
lifetime
technical
support
, email us at [email protected].
HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY
The 6500W will require approximately 30 minutes to assemble with common hand tools.
5
Remove and identify all loose parts from carton.
5
Clean and dry your Cultivator thoroughly after each use.
5
Coat all metal surfaces with a light oil to prevent corrosion and wood sealer to the handles
Bend
5-2014 Pt. 52161