PASCO OS-8526A X-Y ADJUSTABLE DIODE LASER - Manual (Page 2)

2
X-Y Adjustable Laser 012-12246A
®
9 VD C 50 0mA
GN D 3.5m m
HOR IZO NTA L
ADJ UST
VER TIC AL
ADJ UST
ON
OFF
POW ER
+9V DC RED LA SER DIO DE
Wav elength
: 650 n m
Outp ut: < 1mW
OS-8
526
A
X-Y
ADJUST
ABLE
DIODE LASER
10101 F
oothill Blvd.
Rose ville , CA 95747 USA
®
Manu fact ured by:
RE D D IOD
E L AS ER
003 -10 496
AVO ID E XPO SUR E
LAS ER L IGH T IS EM ITTE D
FRO M TH IS A PER TUR E
®
OS -85
26A
X-Y
ADJUST
ABLE
DIODE LASER 10101 F
oothill Blvd.
Rose ville , CA 95747 USA
®
Man ufac ture d by :
Complies with FDA
performance st
andards for
laser product
s except for
deviations
pursuant
to Laser
Notice No. 50, dated June 24, 2007
LASER LIGHT DO NOT ST
ARE
INT
O BEAM
CLASS 2 LASER PRODUCT 650nm, <1mW CW (Red) CLASSIFIED 60825-1 2007
Technical Support
For assistance with any PASCO product, contact
PASCO at:
Address: PASCO scientific
10101 Foothills Blvd.
Roseville, CA 95747-7100
Phone: 916-786-3800 (worldwide)
800-772-8700 (U.S.)
Fax: (916) 786-7565
Web: www.pasco.com
Email: [email protected]
Limited Warranty
For a description of the product warranty, see the
PASCO catalog.
➤ ➤ ➤ ➤ ➤ NOTE: NO service or maintenance is al-
lowed, on this product, by the customer. Return
unit to the factory for service or repair.
Unit is NOT to be opened or modified by the
Customer
Copyright
The PASCO scientific OS-8528A Diode Laser is
copyrighted with all rights reserved. Permission is
granted to non-profit educational institutions for re-
production of any part of this manual, providing the
reproductions are used only in their laboratories and
classrooms, and are not sold for profit. Reproduction
under any other circumstances, without the written
consent of PASCO scientific, is prohibited.
Trademarks
PASCO and PASCO scientific are trademarks or regis-
tered trademarks of PASCO scientific, in the United
States and/or in other countries. All other brands,
products, or service names are or may be trademarks
or service marks of, and are used to identify, products
or services of, their respective owners. For more infor-
mation visit www.pasco.com/legal.
Figure 2: X-Y Adjustable Diode Laser Alignment
laser diode
assembly
“fixed” rod
clamp
thumbscrew
support rod
locking knob
input jack
(9VDC)
adjustment
screws
Figure 3: Laser Beam Fine Adjustment
➁
Secure the rod clamp in place with the thumb-
screw.
➂
Loosen the locking knob and rotate the laser diode
assembly into the desired position. See Figure 2.
➃
Tighten the locking knob against the laser diode
housing until secure.
➄
Plug the 9VDC adapter phone plug into the back
of the laser and turn on the laser.
➅
If necessary, adjust the direction of the laser beam
from left-to-right and up-and down until the beam is in
desired position. See Figure 3.
power switch