12 i 12 j – Dixon Valve 50 TON RAM SEC05 External Swaged Cam And Groove User Manual
Page 9
Cam & Groove Holedall Couplings
customer service
800
•
355
•
1991
7
Section 5
50 Ton Ram Instruction Manual
12i
12j
Position a rubber sheet or pad under the die bed.
While holding the die in place with one hand, loosen
the bolt on the tie down bar and move the tie down
bar so that it clears the die.
Slowly slide the hose
towards the pusher. When the die clears the die
holder, one or both halves may fall to the floor. If
one half remains on the ferrule, tap it with a mallet
until it releases. If both halves remain on the ferrule,
it may require the halves be pried apart at the seam.
Remove the spacer rings from the coupling. Wipe
off excess lubricant from hose and ferrule. Bring the
hose with stem and ferrule back through the die bed.
Reinstall the gasket. Close the cam arms.
Note: Remove spacer ring from the 1½" size only.
- Safety Opening Minds (2 pages)
- SOS van (2 pages)
- Railcar Unloading assemblies (1 page)
- One Piece 8 Frac Fitting" (2 pages)
- Newsletter:February:Search:Safety (2 pages)
- Literature Order Form (1 page)
- KC CW 2014 (1 page)
- Flotech FT470 (1 page)
- F40 tool (2 pages)
- F38 tool (2 pages)
- F175 tool (2 pages)
- F100 tool (2 pages)
- F1 Tool (2 pages)
- CW CH Reg April 2014 (1 page)
- C2 tool (2 pages)
- 51960 tool (2 pages)
- Coupling Inserter CI96 (2 pages)
- CI9 Large Diameter Coupling Inserter (2 pages)
- Manual crimper for Brass ferrules: 860 and 855 (2 pages)
- CM400 crimper (2 pages)
- 5111A Brass Ferrule Crimper (4 pages)
- 1765A Brass Ferrule Crimper (5 pages)
- HB Coupling Expander (6 pages)
- 15 TON RAM Internal Expanded Holedall Petroleum (5 pages)
- 15 TON RAM Internal Expanded Carbon And Stainless Couplings (4 pages)
- 15 TON RAM - Parts List (4 pages)
- 25 TON RAM SEC10 Parts and Attachments (12 pages)
- 50 TON RAM SEC09 Internal Expanded Holedall Petroleum (3 pages)
- 25 TON RAM SEC08 Product Updates (4 pages)
- 25 TON RAM SEC07 Holedall Petroleum IX (4 pages)
- 25 TON RAM SEC06 Internal Expanded Carbon Stainless Couplings (5 pages)
- 25 TON RAM SEC05 Converting (4 pages)
- 25 TON RAM SEC04 External Swaged Cam and Groove (8 pages)
- 25 TON RAM SEC03 External Swaged RST and GAS (5 pages)
- 25 TON RAM SEC02 External Swaged Holedall (6 pages)
- 25 TON RAM SEC01 Holedall Fittings (35 pages)
- 25 TON RAM Complete Manual (89 pages)
- 50 TON RAM SEC10 Parts And Attachments (5 pages)
- 50 TON RAM SEC08 Internal Expanded Carbon And Stainless Couplings (5 pages)
- 50 TON RAM SEC07 Converting (3 pages)
- 50 TON RAM SEC06 External Swaged Ground Joint (7 pages)
- 50 TON RAM SEC04 External Swaged RST and GAS (6 pages)
- 50 TON RAM SEC03 External Swage Holedall with Jackscrews (8 pages)
- 50 TON RAM SEC02 External Swaged Holedall (6 pages)