Dixon Valve 51960 tool User Manual
Screw-action type
BAND CLAMP TOOL
Hold the tool in the left hand so that the cutter bail
is on the bottom and the pulling dog lever is on top.
Slide the strap tail through the slot on the right side
of the tool.
Press down on pulling-dog lever and rotate handle to
begin tightening. Tighten strap to desired tension.
Simultaneously relieve some tension while pushing
the tool away as far as possible.
Pull the cutter bail to cut the strap tail. Tap the
buckle ears down to hold the cut strap tail in place.
1
2
3
Operating Instructions for the 51960 Installation Tool
51960
Screw-action type
For installing band and buckle type clamps
See also other documents in the category Dixon Valve Tools:
- Safety Opening Minds (2 pages)
- SOS van (2 pages)
- Railcar Unloading assemblies (1 page)
- One Piece 8 Frac Fitting" (2 pages)
- Newsletter:February:Search:Safety (2 pages)
- Literature Order Form (1 page)
- KC CW 2014 (1 page)
- Flotech FT470 (1 page)
- F40 tool (2 pages)
- F38 tool (2 pages)
- F175 tool (2 pages)
- F100 tool (2 pages)
- F1 Tool (2 pages)
- CW CH Reg April 2014 (1 page)
- C2 tool (2 pages)
- Coupling Inserter CI96 (2 pages)
- CI9 Large Diameter Coupling Inserter (2 pages)
- Manual crimper for Brass ferrules: 860 and 855 (2 pages)
- CM400 crimper (2 pages)
- 5111A Brass Ferrule Crimper (4 pages)
- 1765A Brass Ferrule Crimper (5 pages)
- HB Coupling Expander (6 pages)
- 15 TON RAM Internal Expanded Holedall Petroleum (5 pages)
- 15 TON RAM Internal Expanded Carbon And Stainless Couplings (4 pages)
- 15 TON RAM - Parts List (4 pages)
- 25 TON RAM SEC10 Parts and Attachments (12 pages)
- 50 TON RAM SEC09 Internal Expanded Holedall Petroleum (3 pages)
- 25 TON RAM SEC08 Product Updates (4 pages)
- 25 TON RAM SEC07 Holedall Petroleum IX (4 pages)
- 25 TON RAM SEC06 Internal Expanded Carbon Stainless Couplings (5 pages)
- 25 TON RAM SEC05 Converting (4 pages)
- 25 TON RAM SEC04 External Swaged Cam and Groove (8 pages)
- 25 TON RAM SEC03 External Swaged RST and GAS (5 pages)
- 25 TON RAM SEC02 External Swaged Holedall (6 pages)
- 25 TON RAM SEC01 Holedall Fittings (35 pages)
- 25 TON RAM Complete Manual (89 pages)
- 50 TON RAM SEC10 Parts And Attachments (5 pages)
- 50 TON RAM SEC08 Internal Expanded Carbon And Stainless Couplings (5 pages)
- 50 TON RAM SEC07 Converting (3 pages)
- 50 TON RAM SEC06 External Swaged Ground Joint (7 pages)
- 50 TON RAM SEC05 External Swaged Cam And Groove (12 pages)
- 50 TON RAM SEC04 External Swaged RST and GAS (6 pages)
- 50 TON RAM SEC03 External Swage Holedall with Jackscrews (8 pages)
- 50 TON RAM SEC02 External Swaged Holedall (6 pages)