Micromod Micro-DCI: 53IT5100B Micro-DCI 4-Channel Indicator Totalizer - Manual (Page 35)

53IT5100B Indicator/Totalizer
INSTRUCTION MANUAL
31
Table 4-3. Analog Input (ANI) Module
Purpose: This module is used to configure input voltage characteristics (e.g., input voltage range), and how the
input signals are interpreted (linear or square root representation).
Title
Symbol ANI Datapoint Default Attribute
Analog
Input
(Display
Only) ANI0
ANI1
ANI2
ANI3 ANI0
ANI1
ANI2
ANI3 H000
H001
H002
H003 0
0
0
0
This is the value in engineering units of the
measured input after all signal conditioning
has been applied.
Engineering
Span
SPAN0
SPAN1
SPAN2
SPAN3 ANI0
ANI1
ANI2
ANI3 C256
C257
C258
C259 100
100
100
100 This determines the upper range the analog
input represents in engineering units. The
upper range value equals Engineering Zero
plus Engineering Span.
Engineering
Zero
ZERO0
ZERO1
ZERO2
ZERO3 ANI0
ANI1
ANI2
ANI3 C276
C277
C278
C279 0
0
0
0
This is the lower range value.
Digital Filter
Index
DFILT0
DFILT1
DFILT2
DFILT3 ANI0
ANI1
ANI2
ANI3 B269
B270
B271
B272 3
3
3
3
This controls a first order filter that is applied
to the input signal. The time constant is
entered as an index value as follows:
0 -No Smoothing (no effect)
1 -0.05 s
2 - 0.1 s
3 - 0.3 s
4 - 0.7 s
5 - 1.5 s
6 - 3.1 s
7 - 6.3 s
8 -12.7 s
9 -25.5 s
10 -51.1 s
11 - 102 s
12 - 205 s
13 - 410 s
14 - 819 s
15 -1638 s
0 - 5 V Input
NOBIAS0
NOBIAS1
NOBIAS2
NOBIAS3 ANI0
ANI1
ANI2
ANI3 L416
L417
L418
L419 0
0
0
0 Setting this parameter to 1 indicates the input
range is from 0 -5 volts (0 -20 mA). 0
indicates the input range is from 1 -5 volts (4 -
20 mA).
Square
Root
Signal
SQRT0
SQRT1
SQRT2
SQRT3 ANI0
ANI1
ANI2
ANI3 L440
L441
L442
L443 0
0
0
0
When a 0, it indicates the analog input signal
should be interpreted linearly.
When 1, it indicates the analog input signal
should be interpreted as a square root
representation of the value. When square root is
selected, input signals less than 1% (10% input
range) forces the input to its zero value.
Calibrate
Zero
CIZ0
CIZ1
CIZ2
CIZ3 ANI0
ANI1
ANI2
ANI3 B263
B264
B265
B266 This is the calibration zero adjustment. This
parameter is factory set and should not need
adjustment under normal operation.
See Section 5.3 for adjustment.
Calibrate
Span
CIS0
CIS1
CIS2
CIS3 ANI0
ANI1
ANI2
ANI3 C296
C297
C298
C299 This is the calibration span adjustment. This
parameter is factory set and should not
need adjustment under normal operation.
See Section 5.3 for adjustment.
Tag Name
AITAG0
AITAG1
AITAG2
AITAG3 ANI0
ANI1
ANI2
ANI3 A224
A225
A226
A227 ANI-0
ANI-1
ANI-2
ANI-3
an assignable 10 character name for the analog
input (ANI-0, ANI-1, ANI-2, ANI-3).
Engineering
Units
AIEU0
AIEU1
AIEU2
AIEU3 ANI0
ANI1
ANI2
ANI3 A298
A299
A300
A301
PERCENT
(ALL)
assignable for units of measure the ANI
represents (e.g., GPM for gallons/minute).