CNB SKB-21Z12F - Manual (Page 20)

• SWING NO. [1~8]
- Selects Swing number to edit. If a selected Swing
SWING SETUP EDIT PATTERN
SWING SETUP
SWING NO 1 ☞
EDIT PATTERN1 EDIT PATTERN1
■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
has not defined, "NOT USED" is displayed in 1st
Position and 2nd Position.
• 1st POS, 2nd POS [PRESET 1~128]
- Set up the 2 position for Swing function.
If a selected preset is not defined, "UNDEFINED“
will be displayed as shown below.
NEAR
SWING NO .
2ND POS .
BACK
EXIT
1
NOT USED
NOT USED
SWING SPEED
CLEAR SWING
CANCEL
1ST POS .
30 /SEC
☞
MOVE TO START POSITION
[NEAR:START /FAR:CANCEL]
[NEAR: SAVE /FAR: DELETE ]
0 /0/x1/N
┏ ┓
┗ ┛
┏ ┓
┗ ┛
RUN SWING GO
◎ When swing function runs, camera moves from the preset assigned as the 1st point
to the preset assigned as the 2nd point. Then camera moves from the preset
assigned as the 2nd point to the preset assigned as the 1st point.
You can not set the same preset.
• SWING SPEED [1 °/sec ~ 180°/sec]
◎ By using Joystick, move to start position with appropriate zoom. To start pattern
recording, press NEAR key. To exit this menu, press FAR key.
◎ Move camera with joystick of controller or run preset function to memorize the path
(mostly curve path) in a selected pattern. The total memory size and the rest memory
size is displayed in the form of bar. Maximum 1200 communication commands can be
EXIT 0 /0/x1/N
SWING SETUP
- Sets Swing speed from 1 °/sec to 180°/sec.
• CLEAR SWING [CANCEL/OK]
- Deletes current Swing data.
• RUN SWING [GO/PREVIEW]
- GO initiates Swing. PREVIEW initiates Swing to preview.
p y
stored in a pattern.
◎ To save data and exit, press NEAR key. To cancel recording and delete record data,
press FAR key.
SWING NO .
2ND POS .
1
PRESET 5
NOT USED
1ST POS . ☞
UNDEFINED
• PATTERN NO. [1~4]
- Selects Pattern number to edit.
If a selected pattern number is not defined
• GROUP NO. [1~8]
- Selects Group number to edit.
If a selected Group number is not defined,
"UNDEFINED" will be displayed under selected
PATTERN SETUP
GROUP SETUP
PATTERN SETUP
PATTERN NO . 1 ☞
GROUP SETUP
GROUP NO .
CLEAR GROUP
☞
1
UNDEFINED
CANCEL
If a selected pattern number is not defined,
"UNDEFINED" will be displayed under selected
pattern number.
• CLEAR PATTERN [CANCEL/OK]
- Deletes data in current pattern.
• EDIT PATTERN
Starts editing pattern
Group number.
• CLEAR GROUP [CANCEL/OK]
- Deletes data in current Group.
• EDIT GROUP
- Starts editing Group.
• RUN GROUP [GO/PREVIEW]
CLEAR PATTERN
BACK
EXIT
UNDEFINED
CANCEL
RUN PATTERN GO
BACK
EXIT
RUN GROUP
CANCEL
RUN GROUP GO
- Starts editing pattern.
• RUN PATTERN [GO/PREVIEW]
- GO initiates Pattern. PREVIEW initiates Pattern to preview.
U G OU [GO/ ]
- GO initiates Group. PREVIEW initiates Group to preview.
38 39