Total access 1200 quad ima module with subtending – ADTRAN 1200 User Manual
Page 2
PRICING AND AVAILABILITY 800.827.0807
TECH SUPPORT 800.726.8663
RETURN FOR REPAIR 256.963.8722
www.adtran.com
61179611L2-22C
Warrant: ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service.
www.adtran.com/warranty
. U.S. and Canada customer Faxback: 877-457-5007, Document 414.
Total Access 1200 Quad IMA Module with Subtending
FRONT PANEL LEDS
T1/E1
{
Off.................................. Facility Unassigned
z
Green.............................. All Good, IMA in Sync
✹
Green (Flashing) ............ T1/E1 OK, no IMA sync
z
Yellow............................ Signal Present, OFF
✹
Yellow (Flashing) .......... T1 is in loopback
z
Red..................................No Signal
ETH
z
Green...............................Ethernet Signal Present
✹
Green (Flashing) ............ Ethernet with traffic
z
Red................................. No Signal
SUB IN
z
Green...............................Connected to an Upstream Box
✹
Green (Flashing) ............ Connected with traffic
{
Off.................................. Not connected
SUB OUT
z
Green.............................. Connected to an Downstream Box
✹
Green (Flashing) ............ Connected with traffic
{
Off.................................. Not connected
COMPLIANCE
This product is NRTL listed to the applicable UL standards. This product is intended to be installed in
a Type “B” or “E” enclosure in a Restricted Access Only area. The Total Access 1200 shelf Frame
Ground terminal must be connected to and earth ground.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN could void the user’s authority to
operate the equipment
PROVISIONING
The Total Access 1200 has a front panel mounted DB–9 connector that supplies an RS–232 interface
for connection to a controlling terminal. The supported terminal type is VT100 or compatible and is
set for 9600 baud, 8 data bits, no parity, and 1 stop bit.
At the Total Access 1200 Login screen, enter the case sensitive account name and password. Note the
the default login is ADMIN and the password is PASSWORD,
and can be changed upon initial
login.
NOTE: To traverse through the menus, select the desired entry, and press
E
NTER
. To work
backward in the menus, press
E
SC
.
Code
Input
Output
Power Code
F
C
Telecommunication Code (TC)
C
X
Installation Code (IC)
A
V
Provisioning Options
Upon initial installation, the module will be provisioned according to factory default settings as show in
the table below. Use the menu screens to make changes as required. The complete menu tree and
provisioning steps are available in the Installation and Maintenance Practice (P/N 61179611L2-5)
Provisioning Options
Settings (Defaults in Bold)
PVCs
User definable; Each ADSL connection must have at least one PVC/PVP for proper
operation (No Default)
Traffic Descriptors
UBR; CBR; VBR–rt; VBR–nrt
Subtend Configuration, mode
Enabled (Master); Disabled (Slave)
T1 Provisioning Options
T1 Type
DSX; T1
T1 Framing
ESF; SF
T1 Line Code
B8ZS; AMI
T1 Line Build Out
DSX Type: 0-133 ft.; 133-266 ft.; 266-399 ft.; 399-533 ft.; 533-655 ft;
T1 Type: 0 dB; –7.5 dB; –15 dB;–22.5 dB
IMA Facility (1-4)
IMA_Group; Pass-through; Unassigned
IMA Transmit ID
0-255 (1 default)
IMA Transmit Frame Length
32; 64; 128; 256
Minimum Tx Active Links
1-4
Minimum Rx Active Links
1-4
Maximum Link Diff Delay
0-100
Group Operation Mode
In Service; Out of Service-Maintenance; Out of Service - Unassigned
ADSL Options
Card Service State
In Service; Out of Service-Maintenance; Out of Service - Unassigned
Line Service State
In Service; Out of Service-Maintenance; Out of Service - Unassigned
Service Mode
Multimode; T.413, G.dmt; G.lite
Link Down Alarm
Disabled; Enabled
Rate Mode
Fixed; Rate Adaptive
Line Type
Interleave; Fast
Target SNR Margin
0-15 dB (6 dB default)
Max SNR Margin
0-31 dB (9 dB default)
Min SNR Margin
0-31 dB
Fast Max Tx Rate
Fast Min Tx Rate
32-8160 kbps Downstream
32-896 kbps Upstream
Interleave Max Tx Rate
Interleave Min Tx Rate
32-7616 kbps Downstream
32-896 kbps Upstream
Interleave Max Delay
5-255 ms (5 ms default)
LOS Secs
0-900 (0 = Disabled)
ES Secs
0-900 (0 = Disabled)