Adsl nim c, Atm c, Atm s – ADTRAN NetVanta ADSL User Manual
Page 2
NetVanta ADSL Network Interface Module (ADSL over ISDN) P/N
1202889E1
For more detailed documentation, visit us online at
Quick Start Guide
®
Quick Start Guide, 61202889E1-13A, November 2006
Copyright © 2006 ADTRAN, All Rights Reserved
Refer to the AOS Command Reference Guide on the
ADTRAN OS System Documentation CD for a
complete list of ATM commands.
ADSL NIM C
OMMANDS
retrain
Forces the modem to retrain.
snr-margin [showtime monitor l training monitor]
during training and showtime. Use the no form of this command to
disable monitoring.
showtime monitor Enables margin monitoring to retrain the ADSL
interface if the specified minimum margin is
violated during showtime.
training monitor
Enables margin monitoring to retrain the ADSL
interface if the specified minimum margin is
violated during training.
Sets the minimum SNR margin in dB. Range is
1 to 15.
training-mode [G.DMT | G.LITE | Multi-Mode | T1.413 | ADSL2 |
ADSL2+ | READSL2]
Configures the ADSL training mode. This setting must either match the
service provider’s DSLAM or be set to Multi-Mode. Note: The following
are the only valid settings for Annex B.
G.DMT
Specifies ANSI full-rate mode. .
Multi-Mode
Specifies auto detect mode.
ADSL2
Specifies ITU G.992.3 mode.
ADSL2+
Specifies ITU G.992.5 mode.
ATM C
OMMANDS
snmp trap link-status
Controls the Simple Network Management Protocol (SNMP) variable
ifLinkUpDownTrapEnable (RFC2863) to enable (or disable) the interface
to send SNMP traps when there is an interface status change. Use the
no form of this command to disable this trap.
ATM S
UB
-I
NTERFACE
C
OMMANDS
access-policy
Use the no form of this command to remove an access policy association.
Identifies the configured access policy using an
alphanumeric descriptor (all access policy descriptors
are case-sensitive).
dynamic-dns [dyndns | dyndns-custom | dyndns-static]
Inc. (www.dyndns.org).
dyndns
Allows you to alias a dynamic IP address to a static
hostname in various domains. This service is provided
for up to five hostnames.
dyndns-custom
Gives complete control over an entire domain name. A
web-based interface provides two levels of control
(basic or advanced) over the domain. Can be used
with both static and dynamic IPs.
dyndns-static
Allows a hostname such as yourname.dyndns.org to
point to your IP address. This service is provided for
up to five hostnames.
encapsulation [aal5mux | aal5snap]
Configures the encapsulation type for the ATM Adaption Layer (AAL) of the
ATM Protocol Reference Model.
aal5mux
Specifies encapsulation type for multiplexed virtual
circuits. A protocol must be specified.
aal5snap
Specifies encapsulation type that supports LLC/SNAP
protocols.
oam-pvc managed
loopback cell generation and OAM management for an ATM interface. Use
the no form of this command to disable generation of OAM loopback cells.
Specifies the time delay between transmitting OAM
loopback cells. Range is 0 to 600 seconds.
oam retry
Use the no form of this command to disable OAM management
parameters.
Specifies number of consecutive end-to-end F5 OAM
loopback cell responses that must be received in order
to change a PVC connection state to up. Range is
1 to 255.
Specifies number of consecutive end-to-end F5 OAM
loopback cell responses that are not received in order
to change a PVC state to down. Range is 1 to 255.
OAM loopback cells are transmitted when a change in
the up/down state of a PVC is being verified. Range is
1 to 600.