BARSKA AU11005 Tactical Red Laser Sight with Flashlight and Mount - Manual

WARNING :
AVOID EXPOSURE
LASER RADIATION IS EMITTED
FROM THIS APERTURE
DANGER
Tactical Red Laser Sight with
Flashlight and Mount
Model: AU11005
Made In China
BARSKA Optics
1721 Wright Ave,
La Verne CA, 91750 USA
This product complies with 21 CFR
chapter 1, subchapter L.
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
Max Output<5mW
WAVELENGTH 635nm-655nm
Class IIIA Laser Product
FDA NO.: 9922878-29
Manufactured 09/2010
REPLACING THE FLASHLIGHT BATTERIES
Remove the light bulb assembly (located in the front end of the
flashlight) by turning the cap counter-clockwise. Place the 3V
battery (CR123A) inside, with the positive end facing out.
Replace the light bulb assembly securely by turning it clockwise
until tight. The flashlight is now ready for use.
EXCHANGING THE FLASHLIGHT SWITCHES
Remove switch assembly from the back of the flashlight by
rotating counterclockwise until loose. Install the new switch by
rotating it clockwise until tight and secure.
REPLACING THE LASER SIGHT BATTERIES
Remove the switch assembly (located in the rear end of the
flashlight) by turning it counter clockwise. Place the three LR44
1.5V batteries inside, with the positive end facing out. Replace
the switch assembly securely by turning it clockwise until tight
and secure. The laser is now ready for use.
POSITIONING THE REMOTE SWITCHES
• Once you have decided the location of the switches on the
rifle stock, place adhesive side of Velcro strip on the stock of
the rifle by pressing the adhesive portion against the stock.
• Attach the other adhesive portion to the back of the pressure
sensitive switches by pressing the adhesive side of the
surface of the Velcro strip against them.
• Secure the pressure sensitive switches to the stock by
pressing both parts of the Velcro together.
ZEROING THE LASER
The laser first needs to be aligned with the path of the pellet/ bullet
to do this follow the steps as described below.
1. Activate the laser by pressing the switch.
2. From a bench rest position, fire three shots at the center of
the target.
3.Observe where the pellets or bullets strike the target.
Keeping the laser dot pointing at the center of the target and
using the windage and elevation adjustment screws located in
the laser body, move the laser dot to the center of the group
formed by the three shots previously fired. Fire three more
shots and note the points of impact on the target. Make
additional adjustment of the laser as necessary.
ADJUSTING THE LASER WINDAGE AND ELEVATION
• The elevation adjustment screw is located on top of the laser. When
the screw is turned counterclockwise, the laser dot will move “up”
and when is turned clockwise the laser dot will move “down”.
• The windage adjustment screw is located at a 45° angle on the right
side of the laser body. When turned counterclockwise, the laser dot
will move to the “right”. When turned clockwise the laser dot will
move to the “left”.
• To align the laser dot with the center of the crosshairs of the reticle,
move it by turning the windage and elevation screws on the laser.
Tactical Red Laser Sight with
Flashlight and Mount
Parts included in package
• Triple mount
• Flashlight
• Laser sight
• 1 Push button and 1 Remote switch for flashlight
• 1 Push button and 1 remote switch for laser sight
• 1 CR123A 3V battery for flashlight
• 3 LR44 1.5V battery for laser sight
• 2 Velcro stickers
• 3 “L” hex wrenches set
©2010 BARSKA ® | La Verne, CA 91750 | USA | www.barska.com BC167
PRECAUTIONS
WARNING: BE CERTAIN THAT YOUR FIREARM IS NOT LOADED AND
POINTED AWAY FROM YOU IN A SAFE DIRECTION. SHOOT ONLY AT AN
APPROVED RANGE OR SUITABLE LOCATION. USE EYE AND EAR
PROTECTION AS NECESSARY.
ATTENTION: THIS BARSKA LASER SIGHT IS A POWERFUL TARGETING
DEVICE THAT REQUIRES SPECIAL ATTENTION WHEN OPERATING.
CAREFULLY READ THE FOLLOWING INSTRUCTIONS AND SAFETY
PRECAUTIONS BEFORE USING THIS PRODUCT.
CAUTION: UNAUTHORIZED USE,
MODIFICATIONS OF ADJUSTMENTS OR
PERFORMANCE OF PROCEDURE OTHER
THAN SPECIFIED HEREIN MAY RESULT IN
DANGEROUS/HAZARDOUS RADIATION
EXPOSURE.
LASER LIGHT: AVOID DIRECT EYE
EXPOSURE. DO NOT LOOK DIRECTLY
INTO THE LASER BEAM OUTPUT
APERTURE DURING OPERATION.
PERMANENT EYE DAMAGE MAY RESULT.
WARNING KEEP OUT OF REACH OF
CHILDREN.
DO NOT POINT LASER AT PEOPLE, PETS,
AIRPLANES, SHINY/HIGHLY REFLECTIVE
SURFACES, OR ANY OTHER OBJECT NOT
INTENDED FOR DESIGNATED USE.