Atec Wiltron-Anritsu-69000A-68000B Series - Manual (Page 5)

231
FREQUENCY SYNTHESIZERS, SIGNAL GENERATORS
5
Without an attenuator
Maximum levelled power to –15 dBm (–20 dBm typical). For units with Option 15 installed, minimum
Levelled output settable power is –5 dBm (–10 dBm typical).
power range
With an attenuator
Maximum levelled power to –115 dBm (–120 dBm typical). For units with upper limit ≥ 50 GHz and units with
Option 15 installed, minimum settable power is –105 dBm (–110 dBm typical).
Without an attenuator >40 dB below max power
With an attenuator >130 dB below max power
Without change in step
attenuator
<1 ms typical
With change in step
attenuator
<20 ms typical
Attenuation
0.01 to
below max
0.05 GHz
0.05 to 20 GHz 20 to 40 GHz 40 to 50 GHz 50 to 60 GHz 60 to 65 GHz
power
0 to 25 dB ±2.0 dB ±1.0 dB ±1.0 dB ±1.5 dB ±1.5 dB ±1.5 dB
Accuracy 25 to 60 dB ±2.0 dB ±1.0 dB ±1.0 dB ±1.5 dB ±3.5 dB –
>60 dB ±2.0 dB ±1.0 dB ±1.0 dB ±2.5 dB ±3.5 dB –
0 to 25 dB ±2.0 dB ±0.8 dB ±0.8 dB ±1.1 dB ±1.1 dB ±1.1 dB
Flatness 25 to 60 dB ±2.0 dB ±0.8 dB ±0.8 dB ±1.1 dB ±3.1 dB –
>60 dB ±2.0 dB ±0.8 dB ±0.8 dB ±2.1 dB ±3.1 dB –
Output power resolution 0.01 dB
Level offset Offsets the displayed power level to establish a new reference level
Range Sweeps between any two power levels at a single CW frequency
Resolution 0.01 dB/step
CW power Accuracy Same as CW power accuracy
sweep
Step size User-controlled, 0.01 dB to the full power range of the instrument
Step dwell time
Variable from 1 ms to 99 seconds. If the sweep crosses a step attenuator setting, there will be a sweep
dwell of approximately 20 ms to allow setting of the step attenuator.
Sweep frequency/step power
A power level step occurs after each frequency sweep. Power level remains constant for length of time
required to complete each sweep.
External AM input
Log AM or linear AM input, front or rear-panel BNC, 50 Ω or 600 Ω input impedance All options selectable
from modulation menu
AM sensitivity
Log AM: Continuously variable from 0 to 25 dB/V
Amplitude Linear AM: Continuously variable from 0 to 100%/V
modulation
AM depth 0 to 90% linear, 20 dB log (typical with RF level at 6 dB below maximum rated output)
AM bandwidth (3 dB) DC to 50 kHz minimum (DC to 100 kHz typical)
Maximum input ±1 V
External FM input Front or rear panel BNC, 50 Ω or 600 Ω input impedance. All options selectable from modulation menu
Frequency
FM sensitivity Variable from ±10 kHz/V to ±20 MHz/V (narrow FM modes) or from ±100 kHz/V to ±100 MHz/V (wide FM mode)* 3
modulation Narrow mode: ±10 MHz, DC to 500 kHz rates
Deviation Wide mode: ±100 MHz, DC to 100 Hz rates
Locked mode: The lesser of ±10 MHz or rate x 300, 1 to 500 kHz rates
On/off ratio >50 dB
Rise/fall time <1 µs typical
Internal square wave
Four square wave signals (400 Hz, 1 kHz, 7.8125 kHz, and 27.8 kHz), selectable from modulation menu
Square wave
generator
Accuracy: Same as internal or external 10 MHz time base
modulation* 4 Square wave symmetry: 50% ±5% at all power levels
Front or rear-panel BNC, selectable from modulation menu
External input
Drive level: TTL compatible input
Minimum pulse width: >5 µs
Input logic: Positive-true or negative-true BNC, selectable from modulation menu
External AM input
Log AM or linear AM input, front or rear-panel BNC, 50 Ω or 600 Ω input impedance
All options selectable from modulation menu
AM sensitivity
Log AM: Continuously variable from 0 to 25 dB per volt
Linear AM: Continuously variable from 0 to 100% per volt
AM depth (typical) 0 to 90% linear; 20 dB log
Amplitude
AM bandwidth DC to 50 kHz minimum (DC to 100 kHz typical)
modulation* 5 Flatness ±0.3 dB (DC to 10 kHz rates)
Accuracy ±5%
Distortion <5% typical
Incidental phase
modulation
<0.2 radians (30% depth, 10 kHz rate)
Maximum input ±1 V
Unleveled
output power
range (typical)
Power level
switching time
(to within speci-
fied accuracy)
Accuracy and
flatness (step
sweep and CW
modes)
69100A/68100B modulation
69200A/69300A/68200B/68300B modulation
RF output
Continued on next page