Atec Fluke-910-910R - Manual (Page 4)

Ordering information
910 GPS-Controlled OCXO Frequency Standard. 5 x 10 MHz and 1
x 5 MHz outputs
910R GPS-Controlled Rubidium Frequency Standard. 5 x 10 MHz
and 1 x 5 MHz outputs
910X-70 5 additional 10 MHz outputs
910X-71 Multiple reference outputs – 0.1 MHz, 1 MHz, 5 MHz and
10 MHz sinewave outputs, plus a 0.1 MHz squarewave output
910X-72 5 additional 2.048 MHz outputs
910X-73 5 additional 13 MHz outputs
910X-75 1 additional pulse output 0.5 Hz to 5 MHz
910X-76 Ethernet interface
Included accessories
Operators manual,
GPSView Software
Optional accessories
PM9622/00 Rack Mount Kit
PM9627 Carrying Case
PM9627H Heavy Duty Aluminium Carrying Case
910X-01 GPS Antenna
910X-01/50 GPS Antenna Mounting Kit
910X-02/20 Antenna Cable, 20 m
910X-02/50 Antenna Cable, 50 m
910X-02/130 Antenna cable, 130 m
Common
Reference outputs (BNC)
10 MHz: Sine wave, 0.6 V rms into 50 Ω
5 MHz: Sine wave, 0.6 V rms into 50 Ω
1 pps: TTL-levels; low < 0.4 V,
high > 2 V into 50 Ω load.
Pulse output (opt. 75): TTL-levels;
low < 0.4 V, high > 2 V into 50 Ω load
10 MHz and 5 MHz outputs
Freq. stability: See frequency stability
specs for 910 and 910R
1-pps output (locked to GPS)
Duty cycle: Approx. 20 %
Jitter: < 60 ns rms relative to UTC
or GPS (position hold, SA on)
5 additional 10 MHz outputs
(option 70)
See specification for 10 MHz above
Multiple reference outputs
(option 71)
Sine wave outputs: 10, 5, 1 and 0.1
MHz > 1 Vrms into 50 Ω
Pulse output: 0.1 MHz; > 3 Vp-p into 50 Ω
0 V ≤ LO < 0.8 V, 3 V < HI ≤ 5 V
5 additional 2.048 MHz out-
puts (option 72)
Frequency: 2.048 MHz square wave
Output level: -1.2 V to +1.2 V ± 10 %
into 75 Ω (G.703:10)
Jitter: < 0.01 UI
5 additional 13 MHz outputs
(option 73)
Output signal: TTL (symmetrical)
Typical levels into 50 Ω:
High voltage: 2.35 V
Low voltage: 0 V
Jitter: < 0.01 UI
Long term stability: Same as main
reference
Pulse output (option 75)
The frequency and duty cycle are set via
the included PC-program
Selectable frequency: N * 1 0
-7
Hz;
N is an integer
Factory default setting: 1 Hz
Jitter: < 500 ps rms
Freq. stability: See frequency stability
specs for 910 and 910R
Ethernet interface (option 76)
Communication port:
Connector: RJ45
Protocol: 10Base-T
Buffer RAM: 1 kbit
Configuration port:
Connector: Dsub9, RS-232
Internal data storage
24h-freq. offset: two-years data,
non-volatile memory
Adjustment data: two-years data,
non-volatile memory
Phase data (TIE): 40-days data,
volatile memory
LED indicators
Locked to GPS, Alarm, Manual Hold-Over
Display indicators
7-segment area:
24h mean freq. offset (if valid data exist)
Time of day (if GPS gives valid time)
“910” or “910R” (if GPS contact not
sufficient)
Alarm text (plus Alarm LED)
REMOTE segment: Local lock-out
(from PC)
Analog bar graph: Satellite signal
strength
GPS-receiver
Antenna connector: Type N
Channels: 8, parallel tracking
Carrier, code: L1, C/A
Antenna (option 01)
Type: Active L1
Operating temp.: -40 °C to +70 °C
Height: 81 mm (3.2 in) (excl.connector)
Weight: 230 g (8 oz)
Gain: > 30 dB
Connector: TNC
Antenna cable
(option 02/20, option 02/50)
Type: RG213
Length: 20 m (02/20), 50 m (02/50)
Connectors: N-type and TNC (male)
Cable delay: 101 ns (02/20), 251 ns
(02/50)
Attenuation:
Approx. 8 dB at 1.6 GHz (02/20)
Approx. 20 dB at 1.6 GHz (02/50)
PC-connection
Interface: RS-232, DTE
Environmental
Temperature: 0 °C to +50 °C (operating)
-40 °C. to +70 °C (storage)
Safety: Compliant to CE: EN
61010-1 + A1 (1992) + A2 (1995)
EMI: Compliant to CE: EN 61326-1 (1997)
Power consumption
Line voltage: 100 V to 240 V (± 10 %)
Line frequency: 47 Hz to 63 Hz
Power 910R: < 75 W at warm-up
< 35 W continuous operation
Power 910: < 25 W at warm-up
< 12 W continuous operation
Dimensions (WxHxD)
315 mm x 86 mm x 395 mm
(12.4 in x 3.4 in x 15.6 in)
Weight
910R (net) 4.4 kg (9.7 lb)
910R (shipping) 7.4 kg (16.3 lb)
910 (net) 3.9 kg (8.6 lb)
910 (shipping) 6.9 kg (15.2 lb)
1
4 Fluke Calibration 910/910R GPS Controlled Frequency Standards
Fluke Calibration
PO Box 9090, Everett, WA 98206 U.S.A.
Fluke Europe B.V.
PO Box 1186, 5602 BD
Eindhoven, The Netherlands
For more information call:
In the U.S.A. (877) 355-3225 or
Fax (425) 446-5116
In Europe/M-East/Africa +31 (0) 40 2675 200 or
Fax +31 (0) 40 2675 222
In Canada (800)-36-FLUKE or
Fax (905) 890-6866
From other countries +1 (425) 446-5500 or
Fax +1 (425) 446-5116
Web access: http://www.flukecal.com
©2000-2013 Fluke Calibration.
Specifications subject to change without notice.
Printed in U.S.A. 7/2013 1567182D_EN
Pub_ID: 10780-eng Rev 03
Modification of this document is not permitted
without written permission from Fluke Calibration.
Fluke Calibration.
Precision, performance, confidence.
™
Various options for calibration
certificates are available; contact
your local Fluke Calibration sales
representative for details.