Atec JDSU-SmartClass-Home - Manual (Page 7)

Specifications and Features
available Configurations
xDSL synch, HPNA testing, Physical layer testing (coax and
twisted pair), Ethernet, Butt-Set, Wireless 802.11b/g WiFi
Physical test interfaces
Coax F-connector for coax mapping, NIT, and HPNA
RJ11 for POTS and HPNA testing
RJ11 for phone wiring and dry pair testing
RJ45 for Cat5/6 wiring and Ethernet testing
RJ45 for VDSL line testing
RJ45 for through mode VDSL testing
Connector LEDs for easy connector identification
xDSl
test interface
ADSL/VDSL2
Single/Bonded
modem Chipset
Broadcom 96368
vDSl Standard Compliance
ITU-T-G.993.2VDSL2 Annex A, B
Profiles; 8a/8b/8c/8d, 12a/12b,17a
Band Plan 997 and 998, u0 Band
aDSl Standard Compliance
ITU-T G.992.1 A, B (G.DMT)
ITU-T G.992.3 A, B, L (ADSL2)
ITU-T G.992.5 Annex A, B, M (ADSL2+)
ANSI T1.413-1998, Issue 2
ITU-T G.992.5 INP Amendment 3
Physical Layer Features
Link state
Actual line rate
Maximum line rate
Capacity
Noise margin
Est. length
Bonded Pair Features
Actual line rate
Maximum line rate
Capacity
Lapse time
xDSL Errors (displays the number of occurrences)
Forward error correction (FEC)
Cyclic redundancy check (CRC)
Severely errored frame (SEF)
Loss of sight (LOS)
Line errors
HPna
Coppergate CG3110 Chipset
Supports only Spectral Mode B: 12-28 MHz;
2, 4, 8, 16 MBauds
Standard Compliance
ITU-T G.995.4
Settings
Configurable Host of Client mode
Configurable Band plan
Configurable IP settings
General Connection Status
Link status
Operating mode
HPNA version
Device list including indication of test set and host
Device MAC identification
HPNA Network Results
Segment specific rate, constellation, and baud
Segment specific packet error rate (PER)
Segment specific SNR
Segment specific receive power
Cable iD and toning
Cable iD Features
Supports coax, Cat3/Cat5/Cat6 cable
Test via F-connector, RJ11, or RJ45
Supports 8 ID devices on each interface
toning Features
Sends four types of tones on all leads
Constant High pitch (976 Hz)
Constant Low pitch (651 Hz)
High pitch then a low pitch
Low pitch with a short high pitch
Coax mapping
Settings
Support any cable coax type with configurable velocity of
propagation (VOP) and cable compensation
Features
Measures cable length in feet (up to 500 ft at ±5 ft)
Measures return loss in dBrl (up to 20 dBrl at ±2 dB)
Cable events identified
Open, splitter, low-quality splitter, barrel/splice
noise immunity test
Features
Measures cable shield isolation vs. settable threshold
(def 30 dB)
Specifications
Test frequency of 88 to 108 MHz
active identification
Features
Identifies coax cables through most coax network elements
Identifies multiple IDs attached to the branch of coax being
tested
Specifications
IDs with up to 15 dB of signal loss between unit and ID
Wiring tool
General Features
Supports Cat3, Cat5/6, coax cable
Detects power present on cables being tested
Measures cable length based on capacitance setting
Detects opens, shorts, and crossed pairs and display wires
mapping
Dry Pair
General Features
Identifies resistive opens and shorts on dry twisted pair
Reports AC voltage presence or DC voltage presence on dry
twisted pair (up to 120 VDC, 120 Vrms AC)
Copper test
Test Range Resolution Accuracy
AC Volts 0 – 300 Peak 1 V 2% ±1 V
DC Volts 0 – 300 1 V 2% ±1 V
(VDC + Peak AC)
resistance
0 – 999 W 1 2% ±2.5 W
1 – 9.99 kW 10 2% ±2.5 W
10 – 99.9 kW 100 2% ±2.5 W
100 – 999 kW 1 k 2% ±2.5 W
1 – 9.9 MW 10 k 6.5% ±2.5 W
10 – 100 MW 100 k 6.5% ±2.5 W
leakage
0 – 999 W 1 2% ±2.5 W
1 – 9.99 kW 10 2% ±2.5 W
10 – 99.9 kW 100 2% ±2.5 W
100 – 999 kW 1 k 2% ±2.5 W
1 – 9.9 MW 10 k 6.5% ±2.5 W
10 – 100 MW 100 k 6.5% ±2.5 W
Distance to Short
0 – 30 k ft/10 km 1 ft/1 m
Capacitance/opens
0 – 2,999 ft/999 m 1 ft/0.1 m 2.5% ±45 pF
0 – 44.9 nF
3 k ft/1 km – 66 k ft/20 km 1 ft/0.1 m 2.5% ±45 pF
45 nF – 1.04 m
DC Current
1 – 110 mA 1 mA ±2% ±1 mA
longitudinal Balance
35 – 70 dB 1 dB 2 dB
Good Ground Check to verify Longitudinal Balance results
load Coil Counter
0 – 27 k ft/8230 m up to 5 ±1
WiFi
Features
Detects all available WiFi (802.11b/g) networks
Reports power level, operating mode, security setting, 802.11
version, channel, SSID, and MAC
ethernet testing
Features
Supports 10/100 Mbps testing over RJ45 interface
Port Discovery
Identifies Ethernet setting on port
Displays link rate
Reports pair skew
Reports frequency offset in ppm
Ping test
Supports manual or DHCP IP configuration
Reports packets sent and received
Reports average test packet delay
7
SmartClaSS Home v3