Atec Anritsu-MG3690 Series - Manual (Page 14)

14
Ordering Information
Models
MG3691C 2 GHz to 10 GHz Signal Generator
MG3692C 2 GHz to 20 GHz Signal Generator
MG3693C 2 GHz to 31.8 GHz Signal Generator
MG3694C 2 GHz to 40 GHz Signal Generator
MG3695C 2 GHz to 50 GHz Signal Generator
MG3697C 2 GHz to 67 GHz Signal Generator (operational to 70 GHz)
Standard (included) Accessories
2300-469 Software for MG3690X
• Operation Manual
• Programming Manual
• SCPI Programming Manual
• IVI Drivers
• Technical Datasheet
Power Cord with plug-type and rating
determined by destination country
3 Year Factory Warranty
Options and Accessories
MG3690C/1A Rack Mount with slides – Rack mount kit containing a set of track
slides (90 degree tilt capability), mounting ears, and front panel
handles to let the instrument be mounted in a standard 19-inch
equipment rack.
MG3690C/1B Rack Mount without slides – Modifies rack mounting hardware
to install unit in a console that has mounting shelves. Includes
mounting ears and front panel handles.
MG3690C/2A Mechanical Step Attenuator – Adds a 10 dB/step attenuator.
MG3690C/2B Rated RF output power is reduced. (This option comes in
MG3690C/2C different versions, based on instrument configuration)
MG3690C/2E Electronic Step Attenuator – Adds a 10 dB/step electronic attenuator
with a 120 dB range for the MG3691C. Rated RF output power
is reduced. (Not available with Option 20 or 22)
MG3690C/3 Ultra Low Phase Noise – Adds new modules to significantly reduce
SSB phase noise. (Not available with Option 3X)
MG3690C/3X Premium Phase Noise, improves Option 3 (< 1 kHz offset).
(Not available with Option 3)
MG3690C/4 8 MHz to 2.2 GHz RF coverage, Ultra-Low Phase Noise
version – Uses a digital down converter to significantly reduce
SSB phase noise. All specifications apply ≥ 10 MHz.
MG3690C/5 8 MHz to 2 GHz RF coverage – Uses an analog down converter.
All specifications apply ≥ 10 MHz.
MG3690C/6 Analog Sweep Capability – (limited to ≥ 500 MHz when used
with Option 4)
MG3690C/7 IF Up-Conversion – Adds an internal 40 GHz mixer for up-converting
an IF signal. (Not available with MG3695C, MG3697C, or with Op-
tions 18, 20 or 36)
MG3690C/8 Power Monitor – Adds internal power measurement capability.
(Not available with Option 9)
MG3690C/9K Rear Panel Output – Moves the RF output connector to the rear
MG3690C/9V panel. (This option comes in different versions, based on instrument
configuration) (Not available with Option 8)
MG3690C/10 User-Defined Modulation Waveform Software – External software
package provides the ability to download user-defined waveforms
into the memory of the internal waveform generator, serially or via
GPIB. External PC and an instrument with LF Generator, Option 27,
are required.
MG3690C/12 Frequency and Phase Modulation – External, via a rear panel BNC
connector. For internal modulation capability, requires additionally
LF Generator, Option 27.
MG3690C/14 Amplitude Modulation – External, via a rear panel BNC connector.
For internal modulation capability, requires additionally
LF Generator, Option 27.
MG3690C/15A High Power – Adds high-power RF components to the instrument
MG3690C/15B to increase its output power level.
MG3690C/15C (This option comes in different versions, based on instrument
MG3690C/15D configuration)
MG3690C/16 High Stability Time Base – Adds an ovenized, 10 MHz
crystal oscillator as a high-stability time base.
MG3690C/17 Delete Front Panel – Deletes the front panel for use in remote
control applications where a front panel display and keyboard control
are not needed. (Only available with Options 1A or 1B)
MG3690C/18 mmW Bias Output – Adds a rear panel BNC Twinax connector
required to bias the 63850 series millimeter wave source modules,
sold separately. Includes DC bias cable. (Not available with
Option 7 or 15x)
MG3690C/20 Scan Modulation – Adds an internal Scan modulator for
simulating high-depth amplitude modulated signals. Requires an
external modulating signal input capability. (Not available on models
MG3693C, MG3694C, MG3695C, MG3697C, or with Options 2E,
7, 15X, or 22)
MG3690C/22 0.1 Hz to 10 MHz Audio coverage – Uses a DDS for coverage down
to approximately DC. When adding Option 22, the output power is
derated by 2 dB. The frequency resolution below 10 MHz is 0.02 Hz.
No modulation is available in the 0.1 Hz to 10 MHz band.
(Not available without Option 4 or 5, or with Option 20 or 2E)
MG3690C/26A Pulse Modulation – External, via a rear panel BNC connector.
MG3690C/26B For internal modulation capability, requires additionally Pulse
Generator, Option 27. (This option comes in different versions,
based on instrument configuration)
MG3690C/27 Internal LF and Pulse Generators – Provides modulation waveforms
for internal AM, FM, ΦM and Pulse. (Not available without
Option 12, 14, or 26)
MG3690C/28A Analog Modulation Suite – For ease of ordering and package
MG3690C/28B pricing, this option bundles Options 12, 14, 26 and 27, offering
internal and external AM, FM, ΦM, and Pulse Modulation.
(This option comes in different versions, based on
instrument configuration)
MG3690C/36 Ultra-Stable Phase Tracking - Provides the capability for ultra-stable
phase tracking between instruments using the internal 100 MHz
reference. (Requires Option 3 or 3x) (Not available with Option 7 or
with both Option 18 and 20 together)
Millimeter Wave Accessories
(Option 18 recommended for DC bias)
63850-15 50 GHz to 75 GHz V band Multiplier Source Module, WR-15
63850-12 60 GHz to 90 GHz E band Multiplier Source Module, WR-12
63850-10 75 GHz to 110 GHz W band Multiplier Source Module, WR-10
63850-08 90 GHz to 140 GHz F band Multiplier Source Module, WR-08
63850-06 110 GHz to 170 GHz D band Multiplier Source Module, WR-06
63850-05 140 GHz to 220 GHz G band Multiplier Source Module, WR-05
63850-03 220 GHz to 325 GHz H band Multiplier Source Module, WR-03
806-121 SMA male-male flexible cable, 90 cm (3 ft) (could be used to
connect the MG3690C output to the module's LO input)