Atec AE-Techron-7224 - Manual (Page 2)

7224 Datasheet Information subject to change. 1/28/2013
DC Specifications
Low Voltage
High Current 5 Min 1 Hr
Volts DC Amps DC Amps DC
24.0 26 20
13.5 20 16
AC Specifications - High Voltage Mode
PEAK OUTPUT RMS OUTPUT
40mSec Pulse,
20% Duty Cycle
5 Minute,
100% Duty Cycle
1 Hour,
100% Duty Cycle
5 Minute,
100% Duty Cycle
1 Hour,
100% Duty Cycle
Ohms Volts Amps Volts Amps Volts Amps Volts Amps Volts Amps Watts
16 158 10 158 10 158 10 112 7 112 7 774
8 154 19 136 16 136 16 96 12 96 12 1108
4 124 31 108 26 61 15 76 18 43 10 442
2 98 49
AC Specifications - Mid-Level Mode
PEAK OUTPUT RMS OUTPUT
40mSec Pulse,
20% Duty Cycle
5 Minute,
100% Duty Cycle
1 Hour,
100% Duty Cycle
5 Minute,
100% Duty Cycle
1 Hour,
100% Duty Cycle
Ohms Volts Amps Volts Amps Volts Amps Volts Amps Volts Amps Watts
4 72 18 69 16 69 16 49 12 49 12 566
2 61 30 57 26 57 26 40 19 40 19 746
1 47 47 43 40 21 21 30 28 15 15 220
0.5 26 52
AC Specifications - High Current Mode
PEAK OUTPUT RMS OUTPUT
40mSec Pulse,
20% Duty Cycle
5 Minute,
100% Duty Cycle
1 Hour,
100% Duty Cycle
5 Minute,
100% Duty Cycle
1 Hour,
100% Duty Cycle
Ohms Volts Amps Volts Amps Volts Amps Volts Amps Volts Amps Watts
1 29 29 29 29 21 21 21 21 420
0.75 26 34 26 34 18 24 18 24 442
0.5 23 45 23 45 16 32 16 32 511
0.25
8-Ohm Power Response:
± 140 Vpk DC to 60 kHz
± 50 Vpk DC to 180 kHz
± 30 Vpk DC to 300 kHz
Slew Rate:
75 V/µSec
Residual Noise:
10 Hz to 300 kHz: 950 µV (0.95 mV)
10 Hz to 80 kHz: 300 µV (0.3 mV)
Signal-to-Noise Ratio:
10 Hz - 30 kHz:
–113 dB
10 Hz - 80 kHz: –106.6 dB
10 Hz - 300 kHz: –99.9 dB
Unit to Unit Phase Error:
± 0.1 degrees at 60 Hz
THD:
DC - 30 kHz less than 0.1%
Output Offset:
7724: Less than ±5 mV
7224P: Less than ±400 µV
DC Drift:
7224: <±1.5 mV
7224P: <±200 µV
(after 20 minutes of operation)
Output Impedance:
28 mOhm in Series with 1 µH
Phase Response:
± 5 degrees (10 Hz - 10 kHz) plus 560 nsec propagation delay
Input Characteristics
Balanced with ground:
Three terminal barrier block connector 20 k ohm differential
Unbalanced:
BNC connector, 10k ohm single ended. Fixed or variable gain
Gain:
Voltage Mode: 20 volts/volt
Current Mode: 5 amperes/volt
Gain Linearity (over input signal, from 0.2V to 5V):
7224: 0.15%
7224P: 0.02% (DC); 0.05% (AC)
Max Input Voltage:
± 10 V balanced or unbalanced