Atec Chroma-62015B Series User Manual

Page 5

SPECIFICATIONS

Model

62015B-15-90

62015B-30-50

62015B-60-25

62015B-80-18

62015B-150-10

Electrical Specifications
Output Ratings

Output Power

1350W

1500W

1440W

1500W

Output Voltage

1~15V

1~30V

1~60V

1~80V

1~150V

Output Current

1~90A

1~50A

1~25A

1~18A

1~10A

Line Regulation

0.1% FS

Load Regulation *1

1% FS

Programming Accuracy

1% FS

Measurement Accuracy

1% FS

Output Noise (20MHz)

Voltage Noise (P-P)

100mV

200mV

400mV

Voltage Ripple (rms)

30mV

50mV

100mV

Current Ripple (rms)

0.9A

0.5A

0.25A

0.18A

0.1A

Efficiency

> 87% @ full load

> 88% @ full load

Turn on over shoot voltage *2

5% of nominal output

Transient Response Time *3

< 5 ms

AC Input Voltage

Six Position Mainframe

187 ~ 250 Vac (3 Phase 4 Wire,

Connection ) or 323 ~ 437 Vac (3 Phase 5 Wire, Y Connection) /

45 ~ 65 Hz

Three Position Mainframe

187 to 250 Vac (single phase) / 45 ~ 65 Hz

Input Power Factor

> 0.98@ full load

Protection Function

OVP

Automatically shuts down at 115% of set value

Adjustment Range

1~16V

1~31V

1~65V

1~83V

1~155V

OCP

Current limit (0 ~ 100%) / OCP Shutdown at 115% of F.S.

OTP

Automatically shuts down if internal limit is reached

I/O Signal

Remote ON/OFF (I/P)

Dry contact (closed = enabled), vice versa

AUX Voltage

4 ~ 24V / 0.5A at mainframe (by trimmer adjust voltage)

DC OK Signal Type (O/P)

Dry contact (closed = enabled) (Error : OVP / OCP / OTP / AC Fault)

Programming Response Time *4 (Typical)

Rise Time (Full Load)

For a programmed 5% to 95% step in output voltage : 100ms

Rise Time (No Load)

For a programmed 5% to 95% step in output voltage : 100ms

Fall Time (Full Load)

For a programmed 95% to 5% step in output voltage : 40ms

Fall Time (No Load)

For a programmed 95% to 5% step in output voltage : 5s

Vout Setting

CAN Bus send command to DC module receiver : 1s

Measurement V & I

Under CAN command using fetch : 100ms

Delay Time

For output ON/OFF enable and disable (under CAN command) : 5s(Single Mainframe)

General Specifications
Remote Sensing

3V max. line loss compensation

Parallel Operation

Current Sharing (

5%)

Operating Temperature

0 ~ 50

℃

Humidity Range

0 ~ 90% RH. Non-condensing

Remote Interface

CAN Bus (optional)

Safety & EMC

Dimension (H x W x D)

Mainframe : 175.6 x 443.9 x 466.2 mm / 6.91 x 17.48 x 18.35 inch (62000B-6-1)

Mainframe : 175.6 x 239.9 x 466.2 mm / 6.91 x 9.44 x 18.35 inch (62000B-3-1)

Module : 138.5 x 67.5 x 377.5 mm / 5.45 x 2.66 x 14.86 inch

Weight

Mainframe : 14 Kg / 30.8 lbs (62000B-6-1)

Mainframe : 8 Kg / 17.6 lbs (62000B-3-1)

Module : 4 Kg / 8.8 lbs

All specifications are subject to change without notice. Please visit our website for the most up to date specifications.

Note*1 :

For 50% step load variation with remote sense at maximum output voltage

Note*2 :

based on rise time of 100ms

Note*3 :

Time for the output voltage to recover within 1% of its rated for a load changed of 25%

Note*4 :

Six Position Mainframe through CAN