Atec California-Instruments_MX Series - Manual (Page 7)

858.458.0223 [email protected] 223
15–135 kVA MX Series II : Specifications
AC Input
Voltage Must be specified at time of order. All inputs are L-L, 3ø, 3 wire + Gnd. 208 ± 10% VAC, 230 ± 10% VAC, 400 ± 10% VAC,
480 ± 10% VAC
Input Line Current (per phase) Current (MX15): Current (MX30/45):
V L-L 208 230 400 480 V L-L 208 230 400 480
St State 58.3 ARMS 52.3 ARMS 30 ARMS 25 ARMS St State 116/175 ARMS 105/157 ARMS 60/90 ARMS 50/75 ARMS
Distortion: < 8 % at full power < 20 % below 35 % of power
Line Frequency 47 - 63 Hz
Efficiency 85 % typical
Power Factor 0.95 typical
AC Service
Inputs/Outputs MX30/MX45: Front access, cables routed through rear panel, exit in back. MX15: Rear Access
Regulatory IEC61010, EN50081-2, EN50082-2, CE EMC and Safety Mark requirements
EMI CISPR 11, Group1 , Class A
Connectors AC Input & Output terminal block behind front cover, IEEE-488 (GPIB) connector (rear panel), 9 pin D-Shell RS232C connector*, (rear
panel), Remote voltage sense terminal block (rear panel), System Interface Connector, DB-37 (rear panel). *RS232 DB9 to DB9 cable
supplied
Physical Dimensions
MX30/MX45 Dimensions Height: 50.0” (1270 mm), Width: 28.75” (731 mm), Depth: 34.5” (876 mm)
MX30/MX45 Weight Chassis: Net: 1150 lbs / 522 Kg, Shipping: 1231 lbs / 560 Kg, Amp Module: Net: 63 lbs / 29 Kg
MX15 Dimensions Height: 31.75” (806 mm), Width: 24.0” (610 mm), Depth: 28.0” (711 mm)
MX15 Weight Chassis: Net: 600 lbs / 272 Kg, Shipping: 681 lbs / 309 Kg, Amp Module: Net: 63 lbs / 29 Kg
Chassis MX30/MX45: Casters and forklift openings. MX15: Casters
Vibration and Shock Designed to meet NSTA project 1A transportation levels. Units are shipped in wooden crate with forklift slots
Air Intake/Exhaust Forced air cooling, front air intake, rear exhaust
Operating Humidity 0 to 95 % RAH, non condensing
Temperature Operating: 0 to 40° C (30° C max in CP mode), Storage: -20 to +85° C
Standard controller versions with single voltage range
Model AC Output Power Phase Outputs AC/DC Voltage Range Controller
MX15-1 15 kVA 1 150/200 or 300/400 Standard
MX30-1 30 kVA 1 150/200 or 300/400 Standard
MX30-3 30 kVA 3 150/200 or 300/400 Standard
MX45-1 45 kVA 1 150/200 or 300/400 Standard
MX45-3 45 kVA 3 150/200 or 300/400 Standard
MX90-3 90 kVA 3 150/200 or 300/400 Standard
MX135-3 135 kVA 3 150/200 or 300/400 Standard
Programmable controller versions with dual voltage ranges
Model AC Output Power Phase Outputs AC/DC Voltage Range Controller
MX15-1Pi 15kVA 1 150/200 & 300/400 Programmable
MX30-3Pi 30 kVA 1 & 3 150/200 & 300/400 Programmable
MX45-3Pi 45 kVA 1 & 3 150/200 & 300/400 Programmable
MX90-3Pi 90 kVA 3 150/200 & 300/400 Programmable
MX135-3Pi 135 kVA 3 150/200 & 300/400 Programmable
Pi models include IEEE-488, RS232C & USB interfaces, Advanced measurements, arbitrary waveform generation. Phase mode switching on MX-30/45-3Pi.
Programmable controller versions with dual voltage ranges
Model AC Output Power Phase Outputs AC/DC Voltage Range Controller
MX90-3Pi-MB 90 kVA 3 150/200 & 300/400 Dual MX45-3Pi
MX135-3Pi-MB 135 kVA 3 150/200 & 300/400 Triple MX-45-3Pi
Reconfigurable systems can be separated into stand-alone MX45-3Pi models or combined for higher power levels.