Atec EMCO-2090 - Manual (Page 3)

Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications. Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications. Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications. Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications. Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications. 2/00 - 2k S © 2000 ETS-EMCO REV B 2/00 - 2k S © 2000 ETS-EMCO REV B 2/00 - 2k S © 2000 ETS-EMCO REV B 2/00 - 2k S © 2000 ETS-EMCO REV B 2/00 - 2k S © 2000 ETS-EMCO REV B
USA:
Tel +1.512.835.4684
Fax +1.512.835.4729
FINLAND:
Tel +358.2.8383.300
Fax +358.2.8651.233
ONLINE:
[email protected]
http://www.emctest.com
2090 115/230 VAC 1 2 A 250 VAC Time Delay 8 fiber optic connectors.
50/60 Hz IEEE-488.2 connector.
IEC 320 power inlet.
Fuse holder.
MODEL WIDTH DEPTH 2 HEIGHT WEIGHT
Physical Specifications
Electrical Specifications
MODEL POWER FUSE BACK PANEL I/0
Positioning Controller
Test Site Hardware
3 33 33
2090 43.8 cm 34.3 cm 13.3 cm 4.5 kg
17.3 in 13.5 in 5.3 in 10.0 lb
Model 2090
2 Excluding handles
optic lines (transmit/receive). Auxiliary
device lines are output only. Reliable and
easy-to-use ST connectors are standard.
GPIB
The General Purpose Interface Bus
(GPIB) complies with IEEE 488.1/488.2
standards. All front panel functions can
be exercised using GPIB commands
while in the remote mode. GPIB com-
mands are backward compatible with
ETS-EMCO Model 1050, 1060 and 1090
Controllers, simplifying upgrades to the
new model. Model 1050 and 1060
commands are compatible with Hewlett
Packard's Model HP 85876A Commercial
Radiated EMI Measurement Software
and Rohde & Schwarz Model ES-KI EMI
Measurement & Evaluation Software.
SSSSSp pp p peed C eed C eed C eed C eed Con on on on ontr tr tr tr trol ol ol ol ol
Users whose test facilities include a two-
speed turntable will find the Model 2090
positioning controller well suited to their
needs. The unit’s SLOW control activates
the turntable’s lower speed drive. The
FAST control activates the turntable’s
higher speed drive. The controller can be
used for speed-control with ETS-EMCO
turntables that feature dual speeds and
other brands of two-speed turntables.
Memory
All settings in the Model 2090 are saved
when the unit is turned off, allowing for
easy set-up when testing is interrupted
and returned to later.
Precise Resolution
Display accuracy on the Model 2090 is
highly precise. The unit offers position
readout increments of 1 mm for towers
and 0.1 degree for turntables.
Universal Power Supply
The positioning controller has a conve-
nient built-in auto ranging feature that
automatically senses supply voltage. Any
AC power source input within the range
of 115/230 VAC, 50/60 Hz can be used.
Rack Mounting
For convenience, the Model 2090 is
standard rack width and 3U rack size.
Standard Configuration
l Controller assembly
l IEC 320 power cord
l Manual
Options
Hand Control Unit
The Hand Control Unit is designed to
manually operate ETS-EMCO antenna
towers and turntables. Lightweight and
easy to operate, this convenient unit
plugs into the motor base of the tower or
turntable and enables you to perform
simple manual movement of these
devices. It works in tandem with ETS-
EMCO’s Model 2090 Controller. Changes
in position location made by the Hand
Control Unit will be recorded and
displayed by the Model 2090 Controller.
To order, specify part number 105136.
Auxiliary Control Unit
The Auxiliary Control Unit provides a
means to remotely open and close
contacts via fiber optic cable. These
contacts can be used to remotely control
power relays or other devices to automate
EMC testing. Simplex fiber optic cable
connects the output of the Model 2090
Aux Control to the input of the Auxiliary
Control Unit. The Auxiliary Control Unit
is powered by a wall-mount power
supply (user-specified 115 VAC or 230
VAC at time of order).
Additional Fiber Optic Cable
Standard fiber optic cable length is 10
meters. Custom lengths are available.
To order, specify part number 708029-m
(10 m increments).
Fiber Optic Feedthrough
Bulkhead feedthrough consisting of a
wave-guide cutoff for fiber optic cable.
To order, specify part number 105120.
Rack Mount Rails
A rack mount kit can be purchased for
mounting the Model 2090 in a rack.
To order, specify part number 540037.
1 Autoselect