Atec Agilent-E4916A - Manual (Page 6)

6
Measurement parameters:
Fr, Fs, Fa, FL, CI, Q, C0, C1, L1, R1,
R0, G0, spurious, DLD, EM, filter
bandwidth
(Note that Fr and Fs represent the
frequencies at which the phase is 0
degree and the maximum conduc-
tance is attained, respectively. You
can also set up the HP E4916A to
search for Fr at which |Z| is minimal.)
Output
Frequency range: 1 MHz to 180 MHz/
1 mHz resolution
Frequency accuracy: 2 ppm (can be
improved up to 0.2 ppm through
external reference input)
Inputs (typical)
Measurement range: 1 MHz to
180 MHz/1 mHz resolution
Impedance: 5 to 125 Ω /10 m Ω
resolution
Return loss: 20 dB
Max. input level: 0 dBm
Damage level: 25 Vdc, 20 dBm
Average noise level: -130 dBm/Hz
Cross talk: -100 dB
Dynamic accuracy:
Input level Level Phase
accuracy accuracy
0 to -20 dBm 0.5 dB 5°
-20 to -30 dBm 0.4 dB 3°
-30 to -40 dBm 0.1 dB 0.6°
-40 to -50 dBm 0.05 dB 0.3°
-50 to -60 dBm 0.05 dB 0.3°
-60 to -70 dBm 0.1 dB 0.6°
-70 to -80 dBm 0.5 dB 5°
-80 to -90 dBm 1.0 dB 10°
General Specifications
Power supply: 90 to 132 V or 198 to
264V, 47 to 63 Hz, 100 VA max.
Operating temperature/humidity:
0 to 55 ° C/15 to 95%
Outer dimensions: 320W × 100H ×
450D mm
Weight: 5.3 kg
Specifications
Others
Interface: HP-IB interface, handler
interface
External reference input: 1/2/5/10
MHz, ± 10 ppm
Equipment supplied with the HP
E4916A:
2 BNC cables (120 cm), 1 operation
manual, 1 user's guide, 4 sample
program disks (VEE run-only
versions included), 1 power cable
Measurement Accuracy
Resonator testing:
Fr: 2 ppm (SPC: Supplemental
Performance Characteristics)
CI: 5% (SPC)
LCR measurements:
Basic accuracy: 3% (SPC)
Impedance measurement range (SPC)
Measurement time (SPC):
The duration of time between the
triggering of the HP E4916A and the
completion of the measurement was
measured. (The time required to
transfer data is not included. The
DLD measurement was made at 5
points; 10 nW, 100 nW, 1 µ W, 10 µ W,
and 100 µ W.)
Frequency Q Fr,CI Fr,CI+ DLD MEAS
EQV TIME
100 MHz 83,000 240 ms 1.02 s 890 ms SHORT
60 MHz 110,000 190 ms 730 ms 775 ms SHORT
24 MHz 135,000 146 ms 680 ms 705 ms SHORT
2 MHz 40,000 280 ms 1.64 s - - MEDIUM
2 MHz - - - - - - 2.57 s LONG
Note: Measurement time may vary
depending on the resonance
frequency even if two resona-
tors of the same type are
tested.
Accessories and Other
Equipment
HP E4915A Crystal Impedance
Meter
Inexpensive model (no variable
power function available with the HP
E4916A)
Frequency range: 1 MHz to 180 MHz
Output power: -5dBm fixed
Comes with all HP E4916A measure-
ment capabilities other than DLD,
EM, and LCR measurement functions.
HP 41900A πππππ Network Test
Fixture
Meets the
IEC444 and JIS
standards. Ideal
for final and
acceptance
inspections.
Can test
resonators with load capacitance
when used in combination with
option 001.
HP41901A SMD πππππ Network Test
Fixture
SMD type π
network test
fixture that
offers superb
repeatability.
Ideal for final
and acceptance
inspections.
Supports 6 types of QIAJ (Quartz
Crystal Industry Association of
Japan) SMDs.