Supplemental characteristics, A - specifications 50 – Atec Agilent-66312A User Manual
Page 3
A - Specifications
50
Supplemental Characteristics
Table A-2 lists the supplemental characteristics, which are not warranted but are descriptions of typical
performance determined either by design or type testing.
Table A-2. Supplemental Characteristics
Parameter Agilent
6611C
Agilent6612C
Agilent 66312A
Agilent 6613C
Agilent 6614C
Input Rating 100 Vac mains:
(at full load ) 120 Vac mains:
220 Vac mains:
230 Vac mains:
100 Vac nominal, 50/60 Hz, 2A, 200 VA max.
120 Vac nominal, 50/60 Hz, 1.7A, 200 VA max.
220 Vac nominal, 50/60 Hz, 0.95A, 200 VA max.
230 Vac nominal, 50/60 Hz, 0.85A, 200 VA max.
Output Programming Voltage:
Range Currrent:
OVP:
0 – 8.190 V
0 – 5.118 A
12 V
0 – 20.475 V
0 – 2.0475 A
0 – 22 V
0 – 51.188 V
0 – 1.0238 A
0-55 V
0 - 102.38 V
0 – 0.5118 A
0 – 110 V
Average Programming Voltage:
Resolution Current:
OVP:
2 mV
1.25 mA
60 mV
5 mV
0.5 mA
100 mV
12.5 mV
0.25 mA
250 mV
25 mV
0.125 mA
500 mV
OVP Accuracy 2.4 % +
200 mV
1
240 mV
600 mV
1.2 V
Maximum Current Measurement
7 A
2.43 A
1.28 A
0.7 A
Average Current High Range:
Measurement Low Range:
Resolution
213 uA
0.6 uA
74 uA
0.6 uA
39 uA
0.6 uA
21 uA
0.6 uA
Sink Current
2
- 3 A
- 1.2 A
- 0.6 A
- 0.3 A
Programming Accuracy Voltage: 0.01% +
Temperature Coefficient Current: 0.01% +
(change/ C
O
) OVP: 0.015% +
0.15 mV
30 uA
2 mV
0.25 mV
12 uA
4 mV
0.5 mV
6 uA
10 mV
1 mV
3 uA
20 mV
Readback Accuracy Voltage: 0.01% +
Temperature Coefficient
(change/C
O
) Current (DC): 0.02% +
Current (ACDC): 0.05% +
Current (Low Range): 0.01% +
60 uV
25 uA
160 uA
0.3 uA
150 uV
10 uA
80 uA
0.3 uA
500 uV
5 uA
40 uA
0.3 uA
700 uV
3 uA
20 uA
0.3 uA
Drift
3
Voltage: 0.01% +
Current: 0.01% +
0.25 mV
50 uA
0.5 mV
20 uA
1 mV
10 uA
1 mV
10 uA
Output Voltage Rise/Fall Time
(for a change from 10% to 90% or
90% to 10% of the total excursion)
2 ms
Output Voltage Settling Time
(to settle within 1 LSB or 0.025% times
the rated voltage of the final value)
6 ms
1
Agilent 6611C Option 760 = 2.4% + 500mV.
2
The sink current does not track the programmed current.
3
Following a 30 minute warm-up, the change in output over 8 hours, under constant ambient, load and line operating conditions.