Specifications – Atec Anritsu-S332D-31D User Manual

Page 10

Specifications

Cable and Antenna Analyzer

Frequency Range:

25 MHz to 4.0 GHz

Frequency Accuracy:

≤±75 ppm @ +25°C

Frequency Resolution:

100 kHz

Output Power:

<0 dBm (–10 dBm nominal)

Immunity to Interfering Signals:

On-channel: +17 dBm

On-frequency: –5 dBm

Measurement Speed:

≤3.5 msec / data point (CW ON)

Number of Data Points:

130, 259, 517

Return Loss:

Range: 0.00 to 60.00 dB

Resolution: 0.01 dB

VSWR:

Range: 1.00 to 65.00

Resolution: 0.01

Cable Loss:

Range: 0.00 to 30.00 dB

Resolution: 0.01 dB

Measurement Accuracy:

>42 dB corrected directivity after calibration

Distance-to-Fault:

Vertical Range: Return Loss: 0.00 to 60.00 dB

VSWR 1.00 to 65.00

Horizontal Range: 0 to (# of data pts –1) x

Resolution to a maximum of 1197m (3929 ft),

# of data pts = 130, 259 or 517

Horizontal Resolution (Rectangular Windowing):

Resolution (meter) = (1.5 x 108) x (Vp)/DF

Where Vp is the cable's relative propagation velocity

and where DF is the stop frequency minus the start

frequency (in Hz).

Spectrum Analyzer (S332D)

Frequency:

Frequency Range:

100 kHz to 3.0 GHz (tunable to 9 kHz)

Frequency Reference

(Internal Timebase) Aging:

±1 ppm/yr

Accuracy: ±2 ppm

Frequency Span:

10 Hz to 2.99 GHz in 1, 2, and 5 step selections

in auto mode, plus zero span

Sweep Time:

≤1.1 sec full span

≤50 µsec to 20 sec selectable in zero span

Resolution Bandwidth (–3 dB):

100 Hz to 1 MHz in 1-3 sequence ±5%

Accuracy

Video Bandwidth (–3 dB):

3 Hz to 1 MHz in 1-3 sequence ±5%

Accuracy typical

SSB Phase Noise (1 GHz) @ 30 kHz Offset:

≤–75 dBc/Hz

Spurious Responses Input Related:

≤–45 dBc

Spurious Residual Responses:

–90 dBm,

≤10 MHz

≤–80 dBm, <10 MHz
(10 kHz RBW, pre-amp on)

Amplitude:

Total Level Accuracy:

±1 dB typical (±1.5 dBm max),

≤10 MHz to 3 GHz

±2 dB typical, <10 MHz for input signal levels
≥–60 dBm, excludes input VSWR mismatch

Measurement Range:

+20 dBm to –135 dBm

Input Attenuator Range:

0 to 51 dB, selected manually or automatically

coupled to the reference level. Resolution in

1 dB steps

Displayed Average Noise Level:

≤–135 dBm, ≥10 MHz (preamp on)

≤–115 dBm, <10 MHz (preamp on) for
input terminated, 0 dB attenuation, RMS

detection, 100 Hz RBW

Dynamic Range:

>65 dB, typical

Display Range:

1 to 15 dB/division, in 1 dB steps, 10 divisions displayed

Scale Units:

dBm, dBV, dB

µV, dBmV, V, W

RF Input VSWR:

(with

≥20 dB atten.), 1.5:1 typical, (10 MHz to 2.4 GHz)

Power Monitor (Option 5)

Detector Range:

1A peak 150 ms, 300 mA max steady state

Offset Range:

–50 to +20 dBm, 10 nW to 100nW

Display Range:

–80 to 80 dBm

Resolution:

0.1 dB, 0.1 xW

Measurement Accuracy:

±1 dB maximum for >–40 dBm and <18 GHz

Bias Tee (Option 10 S332D only)

Voltage:

+18 Vdc

Current:

1A peak 200 ms, 300 mA max steady state

Transmission Measurement (Option 21 S332D only)

Frequency Range:

25 MHz to 3.0 GHz

Frequency Resolution:

10 Hz

Output Power Level:

–10 dBm typical

Dynamic Range:

80 dB, 25 MHz to 2 GHz

60 dB, >2 GHz to 3 GHz

Output Impedence:

Ω

Channel Scanner (Option 27)

Frequency Range:

100 kHz to 3.0 GHz

Frequency Accuracy:

±10 Hz + Time base error, 99% confidence level

Measurement Range:

+20 dBm to –100 dBm

Channel Power:

±1 dB typical (±1.5 dB max)

Adjacent Channel Power Accuracy:

±0.75 dBc

Power Meter (Option 29)

Frequency Range:

3 MHz to 3.0 GHz

Measurement Range:

–80 dBm to +20 dBm (+80 dBm with

60 dB external attenuator)

Display Range:

–80 dBm to +80 dBm

Offset Range:

0 to +60 dB

Accuracy**:

±1 dB typical (±1.5 dBm max), >2 GHz to 3 GHz

±0.5 dB typical (±1 dB max),

≥10 MHz to 2 GHz

±2 dB typical, 3 MHz to <10 MHz

VSWR:

1.5:1 typical (P

>–30 dBm, 10 MHz to 2.4 GHz)

Maximum Power:

+20 dBm (0.1W) without external attenuator

**(Excludes Input VSWR)

GPS (Option 31)

GPS Location Indicator

Latitude, Longitude, and Altitude on Display

Latitude, Longitude, and Altitude with trace storage

T1 Analyzer (Option 50 S331D Only)

Line Coding:

AMI, B8ZS

Framing Modes:

D4 (Superframe)

ESF (Extended Superframe)

Connection Configurations:

Terminate (100

Ω)

Bridge (

≥1000Ω)

Monitor (Connect via 20 dB pad in DSX)

Receiver Sensitivity:

0 to –36 dBdsx

Transmit Level:

0 dB, –7.5 dB, and –15 dB

Clock Sources:

External

Internal 1.544 MHz ±30 ppm

Pulse Shapes:

Conform to ANSI T1.403

Pattern Generation and Detection:

PRBS: 2-9, 2-11, 2-15, 2-20, 2-23

Inverted and non-inverted, QRSS,

1-in-8 (1-in-7), 2-in-8, 3-in-24,

All ones, All zeros, T1-Daly,

User defined (

≤32 bits)

Circuit Status Reports:

Carrier present, Frame ID and Sync,

Pattern ID and Sync

Alarm Detection:

AIS (Blue Alarm), RAI (Yellow Alarm)

Error Detection:

Frame Bits, Bit, BER, BPV, CRC, Error Sec

Error Insertion:

Bit, BPV, Framing Bits, RAI, AIS

Loopback Modes:

Self loop, CSU, NIU, User defined, In-band or Data Link

Level Measurements:

Vp-p (± 5%)

Data Log:

Continuous, up to 48 hrs.

E1 Analyzer (Option 50 S331D only)

Line Coding:

AMI, HDB3

Framing Modes:

PCM30, PCM30CRC, PCM31, PCM31CRC

Connection Configurations:

Terminate (75

Ω, 120Ω)

Bridge (

≥1000Ω)

Monitor (Connect via 20 dB pad in DSX)

Receiver Sensitivity:

0 to –43 dB

Transmit Level:

0 dB, –7.5 dB, and –15 dB

Clock Sources:

External

Internal 2.048 MHz ±30 ppm

Pulse Shapes:

Conform to ITU G.703

Pattern Generation and Detection:

PRBS: 2-9, 2-11, 2-15, 2-20, 2-23

Inverted and non-inverted, QRSS,

1-in-8 (1-in-7), 2-in-8, 3-in-24, All

ones, All zeros, T1-Daly, User defined

(

≤32 bits)

Circuit Status Reports:

Carrier present, Frame ID and Sync, Pattern ID

and Sync

Alarm Detection:

AIS, RAI, MMF

Error Detection:

Frame Bits, Bit, BER, BPV, CRC, E-Bits, Error Sec

Error Insertion:

Bit, BPV, Framing Bits, RAI, AIS

Loopback Modes:

Self loopback

Level Measurements:

Vp-p (±5%)

Data Log:

Continuous, up to 48 hrs.

General

Language Support:

Chinese, English, French, German, Japanese, Spanish

Internal Trace Memory:

200 traces

Setup Configuration:

S332D - 20, S331D - 25

Display:

TFT color LCD with adjustable backlight

Inputs and Outputs Ports:

RF Out: Type N, female, 50

Ω

Maximum Input without Damage: +23 dBm, ±50 VDC

RF In: Type N, female, 50

Ω

Maximum Input without Damage: +43 dBm (peak), ±50 VDC

Ext. Trig In: BNC, female (5V TTL) (S332D Models only)

Ext. Freq Ref In (2 to 20 MHz): Shared BNC, female, 50

Ω,

(–15 dBm to +10 dBm) (S332D Models only)

T1/E1 (Receive and Transmit): Bantam Jack

(S331D Models with Option 50 only)

Serial Interface: RS-232 9 pin D-sub, three wire serial

Electromagnetic Compatibility:

Meets European Community requirements for CE marking

Safety: Conforms to EN 61010-1 for Class 1 portable equipment

Temperature:

Operating: –10°C to 55°C, humidity 85% or less

Non-operating: –51°C to +71°C (Recommend the battery be stored

separately between 0°C and +40°C for any prolonged

non-operating storage period.)

Environmental:

MIL-PRF-28800F Class 2

Power Supply:

External DC Input:

+12.5 to +15 volt dc, 3A max

Internal NiMH battery:

10.8 volts, 1800 mAH

Dimensions:

Size (w x h x d): 25.4 cm x 17.8 cm x 6.1 cm (10.0 in x 7.0 in x 2.4 in)

Weight: <2.28 kg (<5 lbs) includes battery