Cla-Val 2100S - Manual (Page 2)

Specifications
When Ordering, Please Specify:
1. Model No. 100S or No. 2100S
2. Valve Size
3. Pattern - Globe or Angle
4. Pressure Class
5. Screwed or Flanged
6. Temperature and fluid to be handled.
7. Static and Flowing Line Pressure.
8. Body & Trim Material
9. Desired Options
10. When Vertically Installed
Purchase Specifications
The Model 100S/2100S shall be a hydraulically operated, diaphragm-actuated, globe or
angle pattern valve. It shall contain a resilient, synthetic rubber disc, having a rectangular
cross-section, contained on three and one-half sides by a disc retainer and disc guide,
forming a tight seal against a single removable seat insert. The diaphragm assembly, con-
taining a valve stem, shall be fully guided at both ends by a bearing in the valve cover and
an integral bearing in the valve seat. This diaphragm assembly shall be the only moving
part and shall form a sealed chamber in the upper portion of the valve, separating operat-
ing pressure from line pressure. The diaphragm shall consist of nylon fabric bonded with
synthetic rubber and shall not be used as a seating surface. Packing glands or stuffing
boxes are not permitted and there shall be no pistons operating the valve or its pilot con-
trols. All necessary repairs shall be possible without removing the valve from the line. All
materials shall be compatible with seawater.
Valve shall be Model 100S/2100S manufactured by Cla-Val, Newport Beach, CA 92659-0325
For assistance in selecting appropriate valve options or valves manufactured with special design requirements, please contact our Regional Sales Office or Factory.
Available Sizes Operating Temp. Range
Fluids
-40° to 180° F
COVER
PIPE PLUG
COVER BEARING
SPRING
STEM NUT
DIAPHRAGM WASHER
DISC RETAINER
BODY
* SPACER WASHERS
DISC GUIDE
SEAT
PIPE PLUG
STEM
SEAT O-RING
STUD
8" and Larger
* DIAPHRAGM
* DISC
* Repair Parts
Seat Screw
8" and Larger
(Globe or Angle)
PIPE PLUG
HEX NUT
8" and Larger
Cover Bolt
6" and Smaller
KO
DISC GUIDE
KO
SEAT
KO Anti-Cavitation
Trim Option
Component Standard Material Combinations
Body & Cover Ductile Iron Cast Steel Bronze
Stainless Steel
Type 316
NI. AL. Bronze
Super Duplex
Stainless Steel
Available Sizes 1 1 ⁄
4
" - 36" 1 1 ⁄
4
" - 16" 1 1 ⁄
4
" -16" 1 1 ⁄
4
" -16" 1 1 ⁄
4
" -16" 1 1 ⁄
4
" -16"
Disc Retainer &
Diaphragm Washer
Cast Iron Cast Steel Bronze Bronze Monel
Super Duplex
Stainless Steel
Trim: Disc Guide,
Seat & Cover Bearing Bronze is Standard
Stainless Steel is optional
Disc Buna-N ® Rubber
Diaphragm Nylon Reinforced Buna-N ® Rubber
Stem, Nut & Spring Stainless Steel
For material options not listed, consult factory.
Cla-Val manufactures valves in more than 50 different alloys.
Materials
Pattern Threaded Flanged Grooved End
Globe 1" - 3" 1" - 36" 1 1 ⁄
2
"-2"- 2 1 ⁄
2
"- 3"- 4"- 6"- 8"
Angle 1" - 3" 2" - 24" 2" - 3" - 4"
Valve Body & Cover
Pressure Class
Flanged Grooved Threaded
Grade Material
ANSI
Standards*
150
Class
300
Class
300
Class
End‡
Details
ASTM A536 Ductile Iron B16.42 250 400 400 400
ASTM A216-WCB Cast Steel B16.5 285 400 400 400
ASTM B62 Bronze B16.24 225 400 400 400
Note: * ANSI standards are for flange dimensions only.
Flanged valves are available faced but not drilled.
‡ End Details machined to ANSI B2.1 specifications.
Valves for higher pressure are available; consult factory for details
Pressure Ratings (Recommended Maximum Pressure - psi)