Cla-Val 210-27/610-27 - Manual (Page 2)

Model 210-27 (Uses Basic Valve Model 100-01)
Model 210-27 Dimensions (In Inches)
Cover Capacity
Liquid Volume
Displaced from
Diaphragm Chamber
When Valve
Opens or Closes
Valve
Size
Displace-
ment
2” .032 gal
2 1/2” .043 gal
3” .080 gal
4” .169 gal
6” .531 gal
8” 1.26 gal
10” 2.51 gal
12” 4.00 gal
14” 6.50 gal
16” 9.57 gal
18” 9.57 gal
20” 12.00 gal
24” 29.00 gal
36” 42.00 gal
Note: The top two flange holes on valve size 36 are threaded to 1 1/2"-6 UNC.
Dimensions
(In inches)
Component Standard Material Combinations
Body & Cover Ductile Iron Cast Steel Bronze
Available Sizes 2" - 36" 2" - 16" 2" - 16"
Disc Retainer &
Diaphragm Washer
Cast Iron Cast Steel Bronze
Trim: Disc Guide,
Seat & Cover Bearing Bronze is Standard
Stainless Steel is Optional
Disc Buna-N ® Rubber
Diaphragm Nylon Reinforced Buna-N ® Rubber
Stem, Nut & Spring Stainless Steel
For material options not listed, consult factory.
Cla-Val manufactures valves in more than 50 different alloys.
Materials
GGGG
DDDD Inlet
AAAA
X
100-01
Grooved
EE
CC
(MAX)
K
J
H
Inlet Outlet
B
(Diameter)
Y
Z
G
GG
GGG
D Inlet
DD
DDD
F
FF
X
100-01
Threaded &
Flanged
A
E
C
(MAX)
K
J
H
Inlet Outlet
AA
AAA
B
(Diameter)
Valve Body & Cover
Pressure Class
Flanged Grooved Threaded
Grade Material
ANSI
Standards*
150
Class
300
Class
300
Class
End‡
Details
ASTM A536 Ductile Iron B16.42 250 400 400 400
ASTM A216-WCB Cast Steel B16.5 285 400 400 400
ASTM B62 Bronze B16.24 225 400 400 400
Note: * ANSI standards are for flange dimensions only.
Flanged valves are available faced but not drilled.
‡ End Details machined to ANSI B2.1 specifications.
Valves for higher pressure are available; consult factory for details
Pressure Ratings (Recommended Maximum Pressure - psi)
Valve Size (Inches) 2 2 1/2 3 4 6 8 10 12 14 16 18 20 24 30 36
A Threaded 9.38 11.00 12.50 — — — — — — — — — — — —
AA 150 ANSI 9.38 11.00 12.00 15.00 20.00 25.38 29.75 34.00 39.00 41.38 46.00 52.00 61.50 63.00 76.00
AAA 300 ANSI 10.00 11.62 13.25 15.62 21.00 26.38 31.12 35.50 40.50 43.50 47.64 53.62 63.24 64.50 76.00
AAAA Grooved End 9.00 11.00 12.50 15.00 20.00 25.38 — — — — — — — — —
B Dia. 6.62 8.00 9.12 11.50 15.75 20.00 23.62 28.00 32.75 35.50 41.50 45.00 53.16 56.00 66.00
C Max. 6.50 7.56 8.19 10.62 13.38 16.00 17.12 20.88 24.19 25.00 39.06 41.90 43.93 54.60 61.50
CC Max. Grooved End 5.75 6.88 7.25 9.31 12.12 14.62 — — — — — — — — —
D Threaded 4.75 5.50 6.25 — — — — — — — — — — — —
DD 150 ANSI 4.75 5.50 6.00 7.50 10.00 12.69 14.88 17.00 19.50 20.81 — — 30.75 — —
DDD 300 ANSI 5.00 5.88 6.38 7.88 10.50 13.25 15.56 17.75 20.25 21.62 — — 31.62 — —
DDDD Grooved End 4.75 — 6.00 7.50 — — — — — — — — — — —
E 1.50 1.69 2.06 3.19 4.31 5.31 9.25 10.75 12.62 15.50 12.95 15.00 17.75 21.31 24.56
EE Grooved End 2.50 2.88 3.12 4.25 6.00 7.56 — — — — — — — — —
F 150 ANSI 3.00 3.50 3.75 4.50 5.50 6.75 8.00 9.50 10.50 11.75 15.00 16.50 19.25 22.50 25.60
FF 300 ANSI 3.25 3.75 4.13 5.00 6.25 7.50 8.75 10.25 11.50 12.75 15.00 16.50 19.25 24.00 25.60
G Threaded 3.25 4.00 4.50 — — — — — — — — — — — —
GG 150 ANSI 3.25 4.00 4.00 5.00 6.00 8.00 8.62 13.75 14.88 15.69 — — 22.06 — —
GGG 300 ANSI 3.50 4.31 4.38 5.31 6.50 8.50 9.31 14.50 15.62 16.50 — — 22.90 — —
GGGG Grooved End 3.25 — 4.25 5.00 — — — — — — — — — — —
H NPT Body Tapping .375 .50 .50 .75 .75 1 1 1 1 1 1 1 1 2 2
J NPT Cover Center Plug .50 .50 .50 .75 .75 1 1 1.25 1.5 2 1.5 1.5 1.5 2 2
K NPT Cover Tapping .375 .50 .50 .75 .75 1 1 1 1 1 1 1 1 2 2
Stem Travel 0.6 0.7 0.8 1.1 1.7 2.3 2.8 3.4 4.0 4.5 5.1 5.63 6.75 7.5 8.5
Approx. Ship Wt. Lbs. 35 50 70 140 285 500 780 1165 1600 2265 2982 3900 6200 7703 11720
X Pilot System 13 14 15 17 29 31 33 36 40 40 43 47 68 79 85
Y Pilot System 9 10 11 12 20 22 24 26 29 30 32 34 39 40 45
Z Pilot System 9 10 11 12 20 22 24 26 29 30 32 34 39 42 47