Cla-Val 350-02/3650-02 - Manual (Page 7)

350-02/3650-02 Purchase Specifications (CRL-33 supplement)
The Electronic Actuated Pressure sustaining Valve shall maintain a constant upstream pressure and shall be capable of remotely chang-
ing this pressure as directed by the hydraulic pressure sustaining pilot and integral electronic actuator. The actuator shall provide the
interface between remote telemetry and valve set point control. It shall compare a remote analog signal with an internal position signal
in the actuator and adjust the hydraulic pilot spring mechanism to the new setting. The remote analog signal input shall be isolated and
reverse polarity protected. A 4-20 mA actuator feedback signal shall be supplied as standard. A second command control input shall be
available from dry contact switch closure for clockwise and counter clockwise rotation. The actuator shall be IP-68 rated for submersible
service.
If power fails, the pilot shall continue to control the main valve to last set point. If remote set point signal is lost, the actuator shall be
programmable to stay at last position or go to 4 mA or to 20 mA value of set point range. Default is last position. The actuator shall be
ranged at the factory to the specific spring range in the pilot control. If other than the default settings are required, these changes shall
be accomplished by using only the manufacturer’s software and USB cable.
The Electronic Actuated Pressure Reducing Valve shall be Cla-Val Model 350-02/3650-02 as manufactured by Cla-Val, Newport Beach, CA.
***Consult Factory
Model 3650-02 (Uses Basic Valve Model 100-20)
100-20 (Globe)
Model 3650-02 Dimensions (In Inches)
100-20 (Angle)
Component Standard Material Combinations
Body & Cover Ductile Iron Cast Steel Bronze
Available Sizes 3" - 48" 3" - 16" 3" - 16"
Disc Retainer &
Diaphragm Washer
Cast Iron Cast Steel Bronze
Trim: Disc Guide,
Seat & Cover Bearing Bronze is Standard
Stainless Steel is Optional
Disc Buna-N ® Rubber
Diaphragm Nylon Reinforced Buna-N ® Rubber
Stem, Nut & Spring Stainless Steel
For material options not listed, consult factory.
Cla-Val manufactures valves in more than 50 different alloys.
Materials
Pressure Ratings (Recommended Maximum Pressure - psi)
Valve Body & Cover
Pressure Class
Flanged
Grade Material
ANSI
Standards*
150 lb. 300 lb.
ASTM A536 Ductile Iron B16.42 250 400
ASTM A216-WCB Cast Steel B16.5 285 400
ASTM B62 Bronze B16.24 225 400
Note: *ANSI standards are for flange dimensions only.
Flanged valves are available faced but not drilled.
Valve Size (Inches) 3 4 6 8 10 12 14 16 18 20 24 30*** 36*** 42*** 48***
A 150 ANSI 10.25 13.88 17.75 21.38 26.00 30.00 34.25 35.00 42.12 48.00 48.00 63.25 65.00 76.00 94.50
AA 300 ANSI 11.00 14.50 18.62 22.38 27.38 31.50 — 36.62 43.63 49.62 49.75 63.75 67.00 76.00 94.50
B Dia. 6.62 9.12 11.50 15.75 20.00 23.62 24.47 28.00 35.44 35.44 35.44 53.19 56.00 66.00 66.00
C Max. 7.00 8.62 11.62 15.00 17.88 21.00 20.88 25.75 25.00 31.50 31.50 43.94 54.60 61.50 61.50
D 150 ANSI — 6.94 8.88 10.69 — — — — — — — — — — —
DD 300 ANSI — 7.25 9.38 11.19 — — — — — — — — — — —
E 150 ANSI — 5.50 6.75 7.25 — — — — — — — — — — —
EE 300 ANSI — 5.81 7.25 7.75 — — — — — — — — — — —
F 150 ANSI 3.75 4.50 5.50 6.75 8.00 9.50 11.00 11.75 15.88 14.56 17.00 19.88 25.50 28.00 31.50
FF 300 ANSI 4.12 5.00 6.25 7.50 8.75 10.25 — 12.75 15.88 16.06 19.00 22.00 27.50 28.00 31.50
H NPT Body Tapping 3 ⁄
8
1 ⁄
2
3 ⁄
4
3 ⁄
4
1 1 1 1 1 1 1 1 2 2 2
J NPT Cover Center Plug 1 ⁄
2
1 ⁄
2
3 ⁄
4
3 ⁄
4 1 1 1 1 ⁄
4
1 1 ⁄
4 2 2 2 2 2 2 2
K NPT Cover Tapping 3 ⁄
8
1 ⁄
2
3 ⁄
4
3 ⁄
4
1 1 1 1 1 1 1 1 2 2 2
Valve Stem Internal
Thread UNF
10-32 1 ⁄
4
-28 1 ⁄
4
-28 3 ⁄
8
-24 3 ⁄
8
-24 3 ⁄
8
-24 3 ⁄
8
-24 3 ⁄
8
-24 1 ⁄
2
-20 1 ⁄
2
-20 1 ⁄
2
-20 3 ⁄
4
-16 3 ⁄
4
-16 M20 M20
Stem Travel 0.6 0.8 1.1 1.7 2.3 2.8 3.4 3.4 3.4 4.5 4.5 6.5 7.5 8.5 8.5
Approx. Ship Wt. Lbs. 45 85 195 330 625 900 1250 1380 1500 2551 2733 6500 8545 12450 13100
X Pilot System 13.00 15.00 27.00 30.00 33.00 36.00 36.00 41.00 40.00 46.00 55.00 68.00 79.00 85.00 86.00
Y Pilot System 10.00 11.00 18.00 20.00 22.00 24.00 26.00 26.00 30.00 30.00 30.00 39.00 40.00 45.00 47.00
Z Pilot System 10.00 11.00 18.00 20.00 22.00 24.00 26.00 26.00 30.00 30.00 30.00 39.00 42.00 47.00 49.00
Note: The top two flange holes on valve sizes 36 thru 48 are threaded to 1 1/2"-6 UNC.