beautypg.com

Installation & operation overview, Mounting the interfaces, Installation and operation – Extron Electronics RGB 202xi VTG User Guide User Manual

Page 7

background image

RGB 202 Rxxxxxiiiii, RGB 202 Rxxxxxiiiii VTG • Installation and Operation

RGB 202 Rxxxxxiiiii, RGB 202 Rxxxxxiiiii VTG • Installation and Operation

Installation and Operation, cont’d

2-3

Tabletop/desktop placement

For tabletop or desktop placement only, install the self-adhesive
rubber feet/pads (provided) onto the four corners of the bottom
of the interface enclosure.

Under-desk mounting

1

.

Attach the optional under-desk mounting brackets
(part #70-077-01) to the interface with the six machine
screws (provided in the mounting kit), as shown below.

2

.

Hold the interface with attached brackets against the
underside of the desk or other furniture. Mark the location
of holes for screws on the desk.

3

.

Drill 1/4” (6.4 mm) deep, 3/32” (2.38 mm) diameter pilot
holes in the table or desk at the marked screw locations
from the underside/inside (concealed side) of the
furniture, where the interface will be located.

4

.

Insert the four wood screws into the pilot holes. Fasten
each screw into the installation surface until just less than
1/4” of the screw protrudes.

5

.

Align the installed screws with the slots in the mounting
brackets, and place the interface against the surface, with
the screws through the bracket slots.

6

.

Slide the interface slightly forward or back, then tighten all
four screws to fasten it in place.

RGB 202

R

VTG

BOOST

LEVEL

CONTR

OL

PEAK

INPUT

1

2

WITH

ADSP

TM

MINI VTG

CENTERING

SX

GA

SV

GA

VG

A

202

VT

G

XG

A

Under-desk mounting

Installation and Operation

Installation and Operation Overview

This is an overview of the installation process. You will find
detailed installation and operation instructions in this chapter.

To install and set up the RGB 202 Rxi and RGB 202 Rxi VTG
interfaces, follow these basic steps:

1

Turn all of the equipment (computers, remote controls,
interface, projector/monitor, local monitor, and speakers
or other audio device) off. Disconnect the power cords
from the power source.

2

Install the rubber feet for tabletop use, or install the
appropriate brackets and furniture or rack mount the
interface. See “Mounting the Interfaces” in this chapter.

3

Attach the input (computers), output (display, local
monitor and audio), and remote control cables. See
“Cabling” in this chapter.

4

Set the rear DIP switches. Use the “Rear Panel” section of
this chapter as a guide.

5

Connect power cords and turn on the devices: output
devices (projector, monitors, speakers), remote control
device, interface, and source computers.

6

Select an input from the front panel toggle switch or the
remote control (keypad, system, or PC).

7

The image should now appear on screen, and sound
should be audible. If not, ensure that all devices are
plugged in and receiving power. Check the cabling and
switch settings, and make adjustments as needed. Select a
different input (or the VTG) to check for a picture and
sound.

If problems persist, see “Troubleshooting” in this chapter,
then call Extron’s customer support hotline, if needed.

8

Adjust horizontal and vertical centering, and also level
and peaking to obtain the best picture.

9

For the RGB 202 Rxi VTG, set up and test the VTG. See
“Operating the VTG” in this chapter.

2-2

Mounting the Interfaces

Select an installation option: tabletop/desktop placement, or
under-desk, through-desk or rack mounting. Follow the
appropriate installation guide on the next three pages.

This manual is related to the following products: