Extron Electronics RCP 2000 - Manual (Page 14)

RCP 2000 • Operation
Operation, cont’d
RCP 2000 • Operation 3-10
S O F T W I P E
LT t o R T
S O F T W I P E
R T t o LT
S O F T W I P E
T P t o B M
S O F T W I P E
B M t o T P
S C U R T
H R Z I N
S C U R T
H R Z O U T
S C U R T
V E R T I N
S C U R T
V E R T O U T
H C U R T
H R Z I N
H C U R T
H R Z O U T
H C U R T
V E R T I N
H C U R T
V E R T O U T
P L U S
W I P E I N
P L U S
W I P E O U T
S Q U A R E
W I P E I N
S Q U A R E
W I P E O U T
T I T L E
W I N D O W
H A R D W I P E
LT t o R T
H A R D W I P E
R T t o LT
H A R D W I P E
T P t o B M
H A R D W I P E
B M t o T P
S t a r t h e r e
Figure 3-8 — Available wipes
To select the duration of a wipe, do the following:
1 . Press and release the Wipe button. The Wipe button lights
and a duration menu appears on the LCD screen, showing
the current duration selected for the wipe.
2 . Rotate the Adjust knob next to the buttons, and select any
wipe duration from 0.2 to 5.0 seconds as indicated on the
LCD screen.
H W L e f t
0 . 2 S e c .
H W L e f t
0 . 3 S e c .
H W L e f t
0 . 4 S e c .
H W L e f t
0 . 5 S e c .
Figure 3-9 — Wipe duration
Implementing an effect
To implement an effect after it has been set up on the RCP 2000,
follow these steps. (For a title effect, see Implementing a title, on
the next page.)
1 . Press the preview input button to display the preview
image on the preview monitor.
2 . Press the Effect button for the desired effect. (If the button
is already lit, you do not need to press it.)
3 . When you want the effect to occur, press the Take button.
The Take button lights, the effect occurs during the time
specified by the duration, and the Take button light turns
off.
- OR-
R E S E T
M O D E 1
R E S E T
M O D E 2
If you want to control the effect by hand, move the T-bar at
the desired rate.
Implementing a title
To implement a title, do the following:
1 . Press the preview input button to display the preview
image on the preview monitor.
2 . Press the Effect button that has been selected for the title.
(If the button is already lit, you do not need to press it.)
3 . When you want the title to begin, press the Take button.
The portion of the program image dissolves to reveal the
title. The Take light remains on.
4 . When you want to end the title, press the Take button
again. The title dissolves during the time specified by the
duration, and the Take button light turns off.
Resetting the Unit
There are three reset modes available by using the Reset button
(item
5 , page 2-2) on the rear panel. The Reset switch is
recessed, so use of a pointed stylus, ballpoint pen, or Extron
Tweeker is suggested.
CAUTION Review the reset modes carefully. Use of the wrong
reset mode may result in unintended loss of flash
memory programming, reassignment of ports, or
unit reboot.
Mode 1 — Pressing and holding the Reset button until the front
panel LCD display shows “Reset Mode 1” (3 seconds),
then immediately pressing the button momentarily (for
less than one second), causes all events to stop running.
The LCD screen displays “Unit reset” when the Mode 1
reset is complete.
Nothing happens if the second, momentary press does
not occur within one second.
Mode 2 — Pressing and holding the Reset button until the front
panel LCD display shows “Reset Mode 2” (5 seconds),
then immediately pressing the button momentarily (for
less than one second) erases all user flash memory, resets
ports to default conditions, and reboots the unit. The LCD
screen displays “Unit reset” when the Mode 2 reset is
complete.
Nothing happens if the second, momentary press does
not occur within one second.
3-11