Extron Electronics PVS 405D Setup Guide - Manual (Page 3)

j IR control port — Connect the wiring from the IR Out port on rear of the MLC to this connector. IR signals on this
connector are passed to the connected PVT wallplate for control of devices, such as BluRay or DVD players.
k Ethernet connectors — Connect LAN cables to these three ports for 10/100 Ethernet connectivity as follows:
1. TCP/IP network (owner furnished), 2. MLC MediaLink controller, 3. Optional network device
Step 4 — Connect power
l DC power connector — When all other cables have been connected, plug the cable with the orange captive screw
connector (supplied with the power supply) from the 12 VDC power source into this receptacle and apply power. The front
panel power LED and an input LED illuminates when the switcher is receiving power.
NOTE: Use only the supplied 12 V, 4 A power supply for this switcher. The PVS 405D power supply can support a typical
system: for example, a PVS 405D, 2 PVT Wallplates, 2 or 4 speakers, an MLC 104 IP Plus with an IRCM DV+, and
a VoiceLift Microphone system. If an additional SCP 104 is used, the MLC 104 IP Plus MUST have its own power
supply.
3
Front Panel Overview
PVS 405D
POLEVAULT SWITCHER
AUDIO LEVEL ADJUST INPUTS
1
2
SELECT
CONFIG R
PEAK
NORMAL
SIGNAL INPUT
3
4 5
AUX
AUDIO PEAK
NORMAL
SIGNAL VOICELIFT
PAGING
SENSOR
SENSITIVITY
3 8 7 4 2 1 10 9 12 11 5 6
a
Power indicator LED — This LED lights green when power is supplied, and amber when in power save mode.
b
Device Reset button — Pressing this inset button resets the switcher to default settings. See the PVS 405D User Guide
for reset mode details.
c
Front panel mini USB configuration port — Connect a computer to this mini USB port (cable not supplied), for device
configuration and upgrading the firmware.
d
Input selection button and
e
LEDs (1-5) — The button selects and switches inputs and the LEDs indicate which input
is active (current input lights green).
f
Aux input LED — This LED indicates when the aux input is active for input level adjustment.
g
Audio input adjustment knobs and
h
level LEDs — The audio input adjustment knob allows the user to adjust the
level of the audio input. The associated LEDs (peak, normal, and signal) indicate the active audio level.
i
VoiceLift input adjustment knobs and
j
level LEDs — The VoiceLift level adjustment knob allows the user to adjust
the VoiceLift (microphone) input level. The associated LEDs (peak, normal and signal) indicate the active audio level.
k
Paging Sensor sensitivity adjustment knob and
l
Status LED — The adjustment knob allows the user to adjust the
sensitivity of the Page Sensor to interrupt program audio during facility broadcasts. The status LED lights when a broadcast
is detected.
3A MAX
POWER
12V
HDMI
1/2
SIG LINK SIG LINK
3/4
INPUTS OUTPUT AUDIO OUT PVS 405D PAGING
SENSOR
PVT IN PVT IN
L R
AUX OVER PVT REMOTE
VOICELIFT
LAN 1 LAN 2 LAN 3
INPUT 5
+V
L R RS-232
Tx Rx
IR
S G G
L R DO NOT
GROUND
OR SHORT
SPEAKER
OUTPUTS
4/8
Ω
AMPLIFIED AUDIO OUT
CLASS 2 WIRING HDMI
1/2
SIG LINK SIG LINK
3/4
INPUTS OUTPUT AUDIO OUT PVS 405D PAGING
SENSOR
PVT IN PVT IN
L R
AUX
VOICELIFT
INPUT 5
+V
L R
MLC 104 IP Plus right side panel
MLS and Power ports
RS-232 12V
MLS PWR
A B
Rx Tx
GROUND GROUND
+12V IN
OVER PVT
IR
S G
LAN 1 LAN 2 LAN 3
L R
4/8
Ω
DO NOT
GROUND
OR SHORT
SPEAKER
OUTPUTS
AMPLIFIED AUDIO OUT
CLASS 2 WIRING
Included power supply is used for both
PVS 405D and MLC 104 IP Plus
Heat Shrink
Over Drain Wires
Figure 3. Power Supply Connections to PVS 405D and MLS 104 IP Plus
Figure 4. Front Panel Features