Extron Electronics Cable Cubby 700 - Manual (Page 2)

Cable Cubby 500 and 700 • Installation Guide (Continued)
2
x.x"
(x.x cm)
x.x"
(x.x cm)
x.x"
(x.x cm)
x.x"
(x.x cm)
30
Table Top
x.x"
(x.x cm)
x.x"
(x.x cm)
XL Models
x.x"
(x.x cm)
x.x"
(x.x cm)
x.x"
(x.x cm)
XL Models
23.5"
(59.7 cm)
29.4"
(74.7 cm)
26.7"
(67.8 cm)
10.6"
(26.9 cm)
30
Table Top
XL Models
9.1"
(23.1 cm)
15.9"
(40.4 cm)
21.9"
(55.6 cm)
XL Models
3.0"
(7.6 cm)
3.0"
(7.6 cm)
Preparing the Table
Cut a hole in the surface where the enclosure will be installed. Read the following information before making a cut.
Determine the best location for the enclosure
Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible.
Ensure that the edge on which the lid opens is oriented correctly.
Ensure that there is ample space under the table for cables.
When installing retractors in the Cable Cubby, ensure that there is enough space for the retractor assembly under the table or
furniture (ee dimensions for the retractors below).
Choose a method for cutting the hole in the table
ATTENTION: The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople.
Exercise care to prevent scarring or damaging the furniture.
ATTENTION: L’ouverture dans la table pour le Cable Cubby devrait être coupée seulement par des artisans autorisés et
qualifiés. Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.
CAUTION: Wear safety glasses when operating power equipment. Failure to comply can result in eye injury.
ATTENTION: Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique. Ne pas respecter cela peut
conduire à une blessure à l’oeil.
Choose one of the following methods for cutting the hole:
Hand Router and Routing Template Jigsaw and Paper Cut-Out Template CNC Wood Router
If using a CNC wood router or other
precise machinery, use the exact
cut-out dimensions for your model
(see the table below).
Visit www.extron.com for Cable Cubby routing
template part numbers and instructions.
Dimensions and cut-out templates are
available online at
www.extron.com .
Product
Cut-out Dimensions
User Access
Width
Side
Dimension
CC 500 5.75"
(14.6 cm)
5.75"
(14.6 cm)
CC 700 7.125"
(18.1 cm)
5.75"
(14.6 cm)
NOTES:
• To prevent objects from impeding cable retraction, ensure at least 3 inches of clearance from the exposed cable side of
the enclosure (see the diagrams below).
• Excess cabling may cause clearance issues. Use zip ties to secure under-table cabling to prevent accidental contact or
entanglement (see
Routing and Connecting Cables on page 6).
Cut-
Out
Templa
te fo
r th
e Extr
on
Cable Cubb
y 500
0.25
"
(0.6
35 cm
) R
User Access
5.75
"
(14.60 cm
)
5.75" (14.60
cm
) 0.25" Trim
Ring Lip Wid
th
2.0"
Trim Ring
’s O
uter Edge
(Do
not cu
t th is line
.)
0.00
” (0.0
0 cm
)
0.02
(0.05 cm
)
+
Table
Clam
p
P/N
68-85
99-0
1 Re
v. A
SURF
AC
E
CUT
-OUT AREA
1.
Confir
m th
e pr
oduct
to be i
nstalle
d.
2. Remo
ve the
surface
cut-o
ut ar
ea
(gr
ay) fr
om the
tem
plate
.
3.
Measure
the c
uto ut and te
mplate
.
4.
Ma rk th
e pos
ition
on t
he
fu
rnitu
re wh
ere the
Ca ble C
ub by 50
0
wi
ll be
insta
lled.
5. D
ou ble c
heck
dimens
ion s and
pos
ition,
th
en c
ut the
ope
ning
.
Pag
e Siz
e: 11"
x 17
"
Prin
t Sc
ale 1:
1
Do not
Shrink
0.25
"
(0.6
35 cm
) R
5.75
"
(14.60 cm
)
5.75" (14.60 cm
)
SURF
AC
E
CUT
-OUT AREA
Cut-O
ut Te mpl ate fo r the Ext ron
Ca ble Cu
bby 50
0
Us er Ac
cess
0.25" Trim Ring Lip W idth
2.0"
Trim Ring ’s O uter E dge
(Do n ot cu t this line .)
0.00 ” (0.0 0 cm )
0.02 (0.0 5 cm )
+
Table Clam p
P/N 68-8 599-0 1 Re v. A
1. Conf irm the pr oduc t to be ins talle d.
2. Remo ve the surf ace c ut-out area
(g ray) f rom the tem plate .
3. Mea sur e th e cut out and tem plate .
4. Mark the p ositio n on the
fu rnitur e w here the Cab le C ubb y 50 0
w ill be ins talle d.
5. D ou ble c heck dim ension
s an d pos ition ,
th en c ut th e ope ning.
Pag e Si ze: 11
" x 17
"
Print Sc ale 1:1
Do not S
hrin k
Jigsaw
Cut O Cut-O
ut T e
C Ca b