Bell & Gossett HS 600D Pilot Mounting Hardware Kits Series 2000 Pressure and/or Temperature Steam Regulators - Manual (Page 2)

2
PILOT MAIN VALVE SIZE A B C D
1 ⁄
2
, 3 ⁄
4
, 1
1 1 ⁄
4
, 1 1 ⁄
2
2
Spring or air 2 1 ⁄
2
3
4
6
1 ⁄
2
, 3 ⁄
4
, 1
1 1 ⁄
4
, 1 1 ⁄
2
2
Combinations 2 1 ⁄
2
3
4
6
1 ⁄
2
, 3 ⁄
4
, 1
1 1 ⁄
4
, 1 1 ⁄
2
2
Temperature 2 1 ⁄
2
3
4
6
Tubing Length Chart
No cutting is required if dimension is marked with an *
7 9 ⁄
16
8 1 ⁄
16
8 1 ⁄
4
9 1 ⁄
8
9 7 ⁄
16
10 5 ⁄
16
12 1 ⁄
4
11 1 ⁄
4
11 3 ⁄
4
*11 15 ⁄
16
12 13 ⁄
16
13 1 ⁄
16
13 15 ⁄
16
*14 7 ⁄
8
7 15 ⁄
16
8 9 ⁄
16
8 13 ⁄
16
9 11 ⁄
16
10
10
15 ⁄
16
12
6 3 ⁄
8
6 3 ⁄
8
6 3 ⁄
8
6 3 ⁄
8
6 3 ⁄
8
6 3 ⁄
8
6 3 ⁄
8
*10
*10
*10
*10
*10
*10
*10
DIMENSIONS ( INCHES )
3 1 ⁄
2
4 13 ⁄
16
*5 11 ⁄
16
5 15 ⁄
16
6 7 ⁄
16
7 15 ⁄
16
*9 9 ⁄
16
3 1 ⁄
2
4 13 ⁄
16
*5 11 ⁄
16
5 15 ⁄
16
6 7 ⁄
16
7 15 ⁄
16
*9 9 ⁄
16
6
6
3 ⁄
4
*8 11 ⁄
16
10 11 ⁄
16
11 3 ⁄
16
13
*16 11 ⁄
16
6
6
3 ⁄
4
*8 11 ⁄
16
10 11 ⁄
16
11 3 ⁄
16
13
*16 11 ⁄
16
5 3 ⁄
16
6
7
7 ⁄
8
9 7 ⁄
8
10 3 ⁄
8
12 3 ⁄
16
15 7 ⁄
8
Tubing Lengths
1. L-Tube
* Apply Sealant Here
A
B
4
3
10
7
6
8
Cut L- tube to appropriate A & B
dimensions listed on Tubing Length
chart.
2. S-Tube
C
D
Cut S- tube to appropriate C & D
dimensions listed on Tubing
Length chart.
9. J-Tube
No cutting of J-tubes is required
• Pipe sealant should be applied to all pipe threads.
Note: Follow manufacturers instructions for applying
pipe sealant. Keep sealant off of the first thread.
• The preformed copper tubing (included in the hardware
kits) may have to be shortened with a tubing cutter.
After cutting, ream the end to restore original tubing
diameter.
INSTALLATION PROCEDURE
STEP 1 - Prepare Hardware and Size Tubing
TOOLS NEEDED:
Tubing cutter, adjustable or pipe wrench.
Do not use PTFE tape.