Asus TS500-E2 - Manual (Page 91)

4 - 1 1 4 - 1 1 4 - 1 1 4 - 1 1 4 - 1 1 A S U S T S 5 0 0 - E 2 A S U S T S 5 0 0 - E 2 A S U S T S 5 0 0 - E 2 A S U S T S 5 0 0 - E 2 A S U S T S 5 0 0 - E 2
3 . 3 . 3 . 3 . 3 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0 or
RAID 1 set LSI Logic Embedded SATA RAID in the Intel
® 6300ESB
Southbridge chip.
These connectors are set to S t a n d a r d I D E S t a n d a r d I D E S t a n d a r d I D E S t a n d a r d I D E S t a n d a r d I D E mode by default. In S S S S S t a n d a r d t a n d a r d t a n d a r d t a n d a r d t a n d a r d
I D E I D E I D E I D E I D E mode, you can connect Serial ATA boot/data hard disk drives to these
connectors. If you intend to create a Serial ATA RAID set using these
connectors, set the C o n f i g u r e S
C o n f i g u r e S C o n f i g u r e S C o n f i g u r e S C o n f i g u r e S----- A T A A T A A T A A T A A T A a s R A I D a s R A I D a s R A I D a s R A I D a s R A I D item in the BIOS to
[Yes]. See section “4.3.4 IDE Configuration” for details.
NCLV-DS2 SATA connectors
SATA2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
• You must install Windows ® 2000 Service Pack 4 or the Windows ® XP
Service Pack 1 before using Serial ATA hard disk drives. The Serial ATA
RAID feature (RAID 0 or RAID 1) is available only if you are using
Windows
® 2000/XP.
• Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1 set.
• When using the connectors in Standard IDE Standard IDE Standard IDE Standard IDE Standard IDE mode, connect the primary
(boot) hard disk drive to the SATA1 connector. Refer to the table on the
next page for recommended SATA hard disk drive connections.