dbx ZonePRO InstallGuide - Manual (Page 3)

IMPORTANT SAFETY INSTRUCTIONS
ELECTROMAGNETIC COMPATIBILITY
This device complies with part 15 of the Fcc Rules and
the product specifications noted on the Declaration of
Conformity. Operation is subject to the following two
conditions:
• this device may not cause harmful interference, and
• this device must accept any interference received,
including interference that may cause undesired opera-
tion.
Operation of this unit within significant
electromagnetic fields should be avoided.
• use only shielded interconnecting cables.
U.K. MAINS PLUG WARNING
A molded mains plug that has been cut off from the cord is
unsafe. Discard the mains plug at a suitable disposal facil-
ity.
NEVER UNDER ANY CIRCUMSTANCES SHOULD
YOU INSERT A DAMAGED OR CUT MAINS
PLUG INTO A 13 AMP POWER SOCKET.
Do not use the mains plug without the fuse cover in place.
Replacement fuse covers can be obtained from your local
retailer. Replacement fuses are 13 amps and musT be
AsTA approved to Bs1362.
DECLARATION OF CONFORMITY
manufacturer’s Name: dbx professional products
manufacturer’s Address: 8760 s. sandy parkway
sandy, utah 84070, usA
declares that the product:
product name: dbx 1260, dbx 1261
dbx 1260m, dbx 1261m
Note: product name may be suffixed by the eu.
product option: None
conforms to the following product specifications:
safety: Iec 60065 -01+Amd 1
emc:
eN 55022:2006
eN 55024:1998
Fcc part 15
supplementary Information:
The product herewith complies with the requirements of the:
Low Voltage Directive 2006/95/ec
emc Directive 2004/108/ec.
Rohs Directive 2002/95/ec
Weee Directive 2002/96/ec
With regard to Directive 2005/32/ec and ec Regulation 1275/2008 of 17 December
2008, this product is designed, produced, and classified as professional Audio equipment and
thus is exempt from this Directive.
Roger Johnsen
Director, engineering
signal processing
8760 s. sandy parkway
sandy, utah 84070, usA
Date: march 9, 2011
european contact: Your local dbx sales and service Office or
harman signal processing
8760 south sandy parkway
sandy, utah
84070 usA
ph: (801) 566-8800
Fax: (801) 568-7583
DECLARATION OF CONFORMITY
manufacturer’s Name: dbx professional products
manufacturer’s Address: 8760 s. sandy parkway
sandy, utah 84070, usA
declares that the product:
product name: dbx 640, dbx 641
dbx 640m, dbx 641m
Note: product name may be suffixed by the eu.
product option: None
conforms to the following product specifications:
safety: Iec 60065 -01+Amd 1
emc:
eN 55022:2006
eN 55024:1998
Fcc part 15
supplementary Information:
The product herewith complies with the requirements of the:
Low Voltage Directive 2006/95/ec
emc Directive 2004/108/ec.
Rohs Directive 2002/95/ec
Weee Directive 2002/96/ec
With regard to Directive 2005/32/ec and ec Regulation 1275/2008 of 17 December
2008, this product is designed, produced, and classified as professional Audio equipment and
thus is exempt from this Directive.
Roger Johnsen
Director, engineering
signal processing
8760 s. sandy parkway
sandy, utah 84070, usA
Date: march 9, 2011
european contact: Your local dbx sales and service Office or
harman signal processing
8760 south sandy parkway
sandy, utah
84070 usA
ph: (801) 566-8800
Fax: (801) 568-7583