10 factory default parameters – R&M Materials Handling ELECTRIC CHAIN HOISTS LoadMate Chain Hoist LM 10 Stepless User Manual
Page 46
LM10 STEPLESS I&M MANUAL/EN/11.30.2010
46/99
This document and the information contained herein, is the exclusive property of R&M Materials Handling, Inc., and represents a non-public, confidential and proprietary trade secret that
may not be reproduced, disclosed to third parties, altered or otherwise employed in any manner whatsoever without the express written consent of R&M Materials Handling, Inc.
Copyright © (2010) R&M Materials Handling, Inc. All rights reserved.
7.5.10 Factory default parameters
Table 13. Default Factory Parameters
400V 100Hz
460V 120Hz
Label
Code
Default
Label
Code
Default
G 1.1. General Parameters
G 2.1. General Parameters
P 1.1.1
Password
0
P 1.1.1
Password
0
P 1.1.2
Accel Time
1.5
P 1.1.2
Accel Time
1.5
P 1.1.3
Decel Time
0.5
P 1.1.3
Decel Time
0.5
P 1.1.4
Min Freq
12
P 1.1.4
Min Freq
12
P 1.1.5
Max Freq
100
P 1.1.5
Max Freq
120
P 1.1.6
Reverse Plugging
100
P 1.1.6
Reverse Plugging
100
P 1.1.7
Stop Function
Ramping
P 1.1.7
Stop Function
Ramping
P 1.1.8
MSFreq2/Slowdown 20
P 1.1.8
MSFreq2/Slowdown 20
P 1.1.9
Multistep Freq 3
50
P 1.1.9
Multistep Freq 3
50
P 1.1.10
Multistep Freq 4
50
P 1.1.10
Multistep Freq 4
50
P 1.1.11
Input set
EP2
P 1.1.11
Input set
EP2 StopLim
G 2.2. Motor Parameters
G 2.2. Motor Parameters
P 1.2.1
Motor Nom Volt
400
P 1.2.1
Motor Nom Volt
460
P 1.2.2
Motor Selection
Free Hoist
P 1.2.2
Motor Selection
Free Hoist
P 1.2.3
Number of Motors
1
P 1.2.3
Number of Motors
1
G 1.2.4 Motor Nominal Values
G 1.2.4 Motor Nominal Values
P 1.2.4.1
Motor Nom Freq
100
P 1.2.4.1
Motor Nom Freq
120
P 1.2.4.2
Motor Nom Curr
4.4
P 1.2.4.2
Motor Nom Curr
4.4
P 1.2.4.3
Nom Flux Curr
2.6
P 1.2.4.3
Nom Flux Curr
2.6
P 1.2.4.4
Current Limit
7
P 1.2.4.4
Current Limit
7
P 1.2.4.5
Motor Cos Phi
0.69
P 1.2.4.5
Motor Cos Phi
0.69
P 1.2.4.6
Autotuning
Not Done
P 1.2.4.6
Autotuning
Not Done
G 1.2.5 U/f Settings
G 1.2.5 U/f Settings
P 1.2.5.1
Zero Freq Volt
4.2
P 1.2.5.1
Zero Freq Volt
4.2
P 1.2.5.2
U/f Mid Volt
4.5
P 1.2.5.2
U/f Mid Volt
4.5
P 1.2.5.3
U/f Mid Freq
3
P 1.2.5.3
U/f Mid Freq
3
P 1.2.5.4
Torque Boost
On
P 1.2.5.4
Torque Boost
On
P 1.2.5.5
IrAdd Motor
100
P 1.2.5.5
IrAdd Motor
100
P 1.2.5.6
IrAdd Generator
0
P 1.2.5.6
IrAdd Generator
0
P 1.2.5.7
Rs Voltage Drop
99
P 1.2.5.7
Rs Voltage Drop
99
G 1.2.6 Brake Control
G 1.2.6 Brake Control
P 1.2.6.1
Start Current
100
P 1.2.6.1
Start Current
100
P 1.2.6.2
Brk Opening Del
0.05
P 1.2.6.2
Brk Opening Del
0.05
P 1.2.6.3
Start DC-Time
0.1
P 1.2.6.3
Start DC-Time
0.1
P 1.2.6.4
Stop DC-Time
0.2
P 1.2.6.4
Stop DC-Time
0.2
P 1.2.6.5
Stop DC-Freq
2
P 1.2.6.5
Stop DC-Freq
2
P 1.2.6.6
Start Freq S1
4
P 1.2.6.6
Start Freq S1
4
P 1.2.6.7
Start Freq S2
3
P 1.2.6.7
Start Freq S2
3
P 1.2.6.8
Brake Stop Freq
3.5
P 1.2.6.8
Brake Stop Freq
3.5
P 1.2.6.9
Min Freq Bias S2
3
P 1.2.6.9
Min Freq Bias S2
3
G 1.3. I/O Parameters
G 1.3. I/O Parameters
P 1.3.1
ROA1
Not Used
P 1.3.1
ROA1
Not Used
P 1.3.2
Ain1 Min Volt
0
P 1.3.2
Ain1 Min Volt
0
P 1.3.3
Ain1 Max Volt
10
P 1.3.3
Ain1 Max Volt
10
P 1.3.4
Aout Function
Motor Curr
P 1.3.4
Aout Function
Motor Curr
P 1.3.5
Aout Zero Curr
0
P 1.3.5
Aout Zero Curr
0
P 1.3.6
Aout Nom Curr
10
P 1.3.6
Aout Nom Curr
10
G 1.4 Protection
G 1.4 Protection
P 1.4.1
Motor Thermal Prot
Not Used
P 1.4.1
Motor Thermal Prot Not Used
P 1.4.2
-
0
P 1.4.2
-
0
P 1.4.3
-
40
P 1.4.3
-
40
P 1.4.4
-
45
P 1.4.4
-
45
P 1.4.5
-
100
P 1.4.5
-
100
G 1.5 Expert
G 1.5 Expert
P 1.5.1
Slow Down Mode
Fast
P 1.5.1
Slow Down Mode
Fast PowerUp
P 1.5.2
S-Curve
0
P 1.5.2
S-Curve
0
P 1.5.3
Ramp Stretching
0
P 1.5.3
Ramp Stretching
0
P 1.5.4
Switching Freg
8
P 1.5.4
Switching Freg
8
P 1.5.5
Brake Chopper
Run
P 1.5.5
Brake Chopper
Run