Rainbow Electronics MAX1182 - Manual (Page 2)

MAX1182
Dual 10-Bit, 65Msps, +3V, Low-Power ADC with
Internal Reference and Parallel Outputs
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(V DD = +3V, OV DD = +2.5V; 0.1µF and 1.0µF capacitors from REFP, REFN, and COM to GND; REFOUT connected to REFIN through
a 10k Ω resistor, V
IN = 2Vp-p (differential w.r.t. COM), C L = 10pF at digital outputs (Note 5), f CLK = 65MHz (50% duty cycle),
T A = T MIN to T MAX , unless otherwise noted. Typical values are at T A = +25°C.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
V DD , OVDD to GND...............................................-0.3V to +3.6V
OGND to GND.......................................................-0.3V to +0.3V
INA+, INA-, INB+, INB- to GND ...............................-0.3V to V
DD
REFIN, REFOUT, REFP, REFN, CLK,
COM to GND ..........................................-0.3V to (V DD + 0.3V)
OE, PD, SLEEP, T/B, D9A–D0A,
D9B–D0B to OGND .............................-0.3V to (OV DD + 0.3V)
Continuous Power Dissipation (T A = +70°C)
48-Pin TQFP (derate 12.5mW/°C above +70°C).......1000mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-60°C to +150°C
Lead temperature (soldering, 10s) ..................................+300°C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
DC ACCURACY
Resolution 10 Bits
Integral Nonlinearity INL f IN = 7.47MHz ±0.6 ±1.9 LSB
Differential Nonlinearity DNL f IN = 7.47MHz, no missing codes guaranteed ±0.4 ±1.0 LSB
Offset Error < ±1 ±1.7 % FS
Gain Error 0 ±2 % FS
ANALOG INPUT
Differential Input Voltage
Range
V DIFF Differential or single-ended inputs ±1.0 V
Common-Mode Input Voltage
Range
V CM
V DD /2
± 0.5
V
Input Resistance R IN Switched capacitor load 33 k Ω
Input Capacitance C IN 5 pF
CONVERSION RATE
Maximum Clock Frequency f CLK 65 MHz
Data Latency 5
Clock
Cycles
DYNAMIC CHARACTERISTICS (f CLK = 65MHz, 4096-point FFT)
f INA or B = 7.47MHz, T A = +25 °C 56.8 59.5
f INA or B = 20MHz, T A = +25 °C 56.5 59 Signal-to-Noise Ratio SNR
f INA or B = 39.9MHz (Note 1) 59
dB
f INA or B = 7.47MHz, T A = +25 °C 56.5 59
f INA or B = 20MHz, T A = +25 °C 56 58.5
Signal-to-Noise and Distortion
(up to 5th harmonic)
SINAD
f INA or B = 39.9MHz (Note 1) 58.5
dB
f INA or B = 7.47MHz, T A = +25 °C 65 76
f INA or B = 20MHz, T A = +25 °C 65 77 Spurious-Free Dynamic Range SFDR
f INA or B = 39.9MHz, (Note 1) 75
dBc