Pin description – Rainbow Electronics DS1393 User Manual
Page 10
DS1390/DS1391/DS1392/DS1393
Low-Voltage SPI/3-Wire RTCs with
Trickle Charger
10
____________________________________________________________________
Pin Description
PIN
DS1390
DS1391
DS1392
DS1393
NAME
FUNCTION
1
1
1
1
X1
2
2
2
2
X2
Connections for Standard 32.768kHz Quartz Crystal. The internal oscillator
circuitry is designed for operation with a crystal having a 6pF specified load
capacitance (C
L
). Pin X1 is the input to the oscillator and can optionally be
connected to an external 32.768kHz oscillator. The output of the internal
oscillator, pin X2, is floated if an external oscillator is connected to pin X1.
3
3
3
3
V
BACKUP
DC Backup Power Input for Primary Cell. This pin is a rechargeable
battery/super cap or a secondary supply. UL recognized to ensure against
reverse charging current when used with a lithium battery.
4
4
—
—
CS
SPI Chip-Select Input. This pin is used to select or deselect the part.
—
—
4
4
CE
Chip Enable for 3-Wire Interface
5
5
5
5
GND
Ground
6
6
—
—
DIN
SPI Data Input. This pin is used to shift address and data into the part.
—
—
6
—
INT
Interrupt Output. This pin is used to output the interrupt signal, if enabled by
the control register. The maximum voltage on this pin is 5.5V, independent
of V
CC
or V
BACKUP
. If enabled, INT functions when the device is powered
by either V
CC
or V
BAT
.
—
9
—
6
RST
Reset. This active-low, open-drain output indicates the status of V
CC
relative
to the V
PF
specification. As Vcc falls below V
PF
, the RST pin is driven low.
When Vcc exceeds V
PF
, for t
RST
, the RST pin is driven high impedance.
This pin is combined with a debounced pushbutton input function. This pin
can be activated by a pushbutton reset request. This pin has an internal,
50k
Ω (typ) pullup resistor to V
CC
. No external pullup resistors should be
connected. If the crystal oscillator is disabled, the startup time of the
oscillator is added to the t
RST
delay.
7
7
—
—
DOUT
SPI Data Output. Data is output on this pin when the part is in read mode.
CMOS push-pull driver.
—
—
7
7
I/O
Input/Output for 3-Wire Interface. CMOS push-pull driver.
8
8
8
8
SCLK
Serial Clock Input. This pin is used to control the timing of data into and out
of the part.
9
—
—
9
SQW/INT
Square-Wave/Interrupt Output. This pin is used to output the programmable
square wave or interrupt signal. When enabled by setting the ESQW bit to
logic 1, the SQW/INT pin outputs one of four frequencies: 32.768kHz,
8.192kHz, 4.096kHz, or 1Hz. This pin is open drain and requires an external
pullup resistor. The maximum voltage on this pin is 5.5V, independent of
V
CC
or V
BACKUP
. If enabled, SQW/INT functions when the device is
powered by either V
CC
or V
BAT
.
—
—
9
—
SQW
Square-Wave Output. This pin is open drain and requires an external pullup
resistor. The maximum voltage on this pin is 5.5V, independent of V
CC
or
V
BACKUP
. If enabled, SQW functions when the device is powered by either
V
CC
or V
BAT
.
10
10
10
10
V
CC
DC Power Pin for Primary Power Supply