Rainbow Electronics MAX9512 - Manual (Page 18)

MAX9512
Video Filter Amplifier with SmartSleep
and Y/C Mixer Circuit
18 _ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to
www.maxim-ic.com/packages .)
EXPOSED PAD VARIATIONS
1.10 T1633-1 0.95
CODES
PKG.
T1233-1
MIN.
0.95
NOM.
1.10
D2
1.25 1.10 0.95 1.25
NOM.
1.10
MAX.
1.25
MIN.
0.95
MAX.
1.25
E2
12 N
k
A2
0.25
NE
A1
ND
0
0.20 REF
- -
3
0.02
3
0.05
L
e
E
0.45
2.90
b
D
A
0.20
2.90
0.70
0.50 BSC.
0.55
3.00
0.65
3.10
0.25
3.00
0.75
0.30
3.10
0.80
16
0.20 REF
0.25 -
0
4
0.02
4
-
0.05
0.50 BSC.
0.30
2.90
0.40
3.00
0.20
2.90
0.70
0.25
3.00
0.75
3.10
0.50
0.80
3.10
0.30
PKG
REF. MIN.
12L 3x3
NOM. MAX. NOM.
16L 3x3
MIN. MAX.
0.35 x 45°
PIN ID JEDEC
WEED-1
0.35 x 45° WEED-2
T1233-3 1.10 1.25 0.95 1.10 0.35 x 45° 1.25 WEED-1 0.95
T1633F-3 0.65
T1633-4 0.95
0.80 0.95 0.65 0.80
1.10 1.25 0.95 1.10
0.225 x 45° 0.95 WEED-2
0.35 x 45° 1.25 WEED-2
T1633-2 0.95 1.10 1.25 0.95 1.10 0.35 x 45° 1.25 WEED-2
NO
DOWN
BONDS
ALLOWED
YES
NO
YES
N/A
NO
PACKAGE OUTLINE
21-0136 2
2
G
8, 12, 16L THIN QFN, 3x3x0.8mm
YES WEED-1 1.25 1.10 0.95 0.35 x 45° 1.25 1.10 0.95 T1233-4
T1633FH-3 0.65 0.80 0.95 0.225 x 45° 0.65 0.80 0.95 WEED-2 N/A
NOTES:
1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
3. N IS THE TOTAL NUMBER OF TERMINALS.
4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO
JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED
WITHIN THE ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR
MARKED FEATURE.
5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.20 mm AND 0.25 mm
FROM TERMINAL TIP.
6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
9. DRAWING CONFORMS TO JEDEC MO220 REVISION C.
10. MARKING IS FOR PACKAGE ORIENTATION REFERENCE ONLY.
11. NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY.
0.25 0.30 0.35
2
0.25
0
0.20 REF
- -
0.02 0.05
0.35
8
2
0.55 0.75
2.90
2.90 3.00 3.10
0.65 BSC.
3.00 3.10
8L 3x3
MIN.
0.70 0.75 0.80
NOM. MAX.
TQ833-1 1.25 0.25 0.70 0.35 x 45° NO WEEC 1.25 0.70 0.25