Technical data – Milton CAT C27 800 kW 1000 kVA 60 Hz 1800 rpm 480 Volts Spec Sheet User Manual
Page 4

®
STANDBY 800 ekW 1000 kVA
60 Hz 1800 rpm 480 Volts
TECHNICAL DATA
Open Generator Set - - 1800 rpm/60 Hz/480 Volts
DM7696
EPA Certified Tier 2
Generator Set Package Performance
Genset Power rating @ 0.8 pf
Genset Power rating with fan
1000 kVA
800 ekW
Coolant to aftercooler temp max
Coolant to aftercooler temp max
49 º C
120 º F
Fuel Consumption
100% load with fan
75% load with fan
50% load with fan
216.6 L/hr
57.2 Gal/hr
171.6 L/hr
45.3 Gal/hr
122.2 L/hr
32.3 Gal/hr
Cooling System
1
Air flow restriction (system)
Air flow (max @ rated speed for radiator arrangement)
Engine Coolant capacity with radiator/exp. tank
Engine coolant capacity
Radiator coolant capacity
0.12 kPa
0.48 in. water
1137 m³/min
40153 cfm
160.0 L
42.3 gal
55.0 L
14.5 gal
105.0 L
27.7 gal
Inlet Air
Combustion air inlet flow rate
61.5 m³/min
2171.9 cfm
Exhaust System
Exhaust stack gas temperature
Exhaust gas flow rate
Exhaust flange size (internal diameter)
Exhaust system backpressure (maximum allowable)
512.8 º C
955.0 º F
171.2 m³/min
6045.9 cfm
203 mm
8 in
10.0 kPa
40.2 in. water
Heat Rejection
Heat rejection to coolant (total)
Heat rejection to exhaust (total)
Heat rejection to aftercooler
Heat rejection to atmosphere from engine
Heat rejection to atmosphere from generator
330 kW
18767 Btu/min
767 kW
43619 Btu/min
157 kW
8929 Btu/min
164 kW
9327 Btu/min
36.8 kW
2092.8 Btu/min
Alternator
2
Motor starting capability @ 30% voltage dip
Frame
Temperature Rise
2131 skVA
597
130 º C
234 º F
Lube System
Sump refill with filter
68.0 L
18.0 gal
Emissions (Nominal)
3
NOx g/hp-hr
CO g/hp-hr
HC g/hp-hr
PM g/hp-hr
5.26 g/hp-hr
.23 g/hp-hr
.03 g/hp-hr
.024 g/hp-hr
1
For ambient and altitude capabilities consult your Caterpillar dealer. Air flow restriction (system) is added to existing restriction from
factory.
2
UL 2200 Listed packages may have oversized generators with a different temperature rise and motor starting characteristics. Generator
temperature rise is based on a 40ºC ambient per NEMA MG1-32.
3
Emissions data measurement procedures are consistent with those described in EPA CFR 40 Part 89, Subpart D & E and ISO8178-1 for
measuring HC, CO, PM, NOx. Data shown is based on steady state operating conditions of 77ºF, 28.42 in HG and number 2 diesel fuel
with 35º API and LHV of 18,390 btu/lb. The nominal emissions data shown is subject to instrumentation, measurement, facility and engine
to engine variations. Emissions data is based on 100% load and thus cannot be used to compare to EPA regulations which use values
based on a weighted cycle.
April 30 2009 16:23 PM
4