Altronix HubSat 4WP Installation Instructions - Manual (Page 2)

- 2 - HubSat4WP
Overview:
Altronix HubSat4WP Passive UTP Transceiver Hub w/Integral Camera Power transmits UTP video, RS422/RS485 data and
power over a single CAT-5 or higher structured cable. Unit provides 4 camera channels in a wall mount enclosure. Video
transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when
utilizing Altronix HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners. In addition, the unit features individual-
ly selectable 24VAC or 28VAC PTC protected outputs with surge suppression. Optionally, the HubSat4WP can be used as
an accessory module to transmit video from up to 4 cameras over a single CAT-5 or higher structured cables back to the
HubWay, HubWayLD or HubWayLDH Passive and Active UTP Transceiver Hubs. In addition, the HubSat4WP provides
power to these cameras locally to eliminate the possibility of voltage drop associated with long cable runs.
Input:
• 115VAC 60Hz, 1.25 amp.
• Primary in-line fuse is rated @ 3.5A/250V.
Video:
• Four (4) channels of quality video over twisted pair
up to a distance of 750 ft. per channel.
• Four (4) 75 ohm video outputs.
Data:
• RS422/RS485 data input.
Power:
• Individually selectable 24VAC or 28VAC power
outputs with OFF position.
• Unit provides up to 1 amp max. per channel not to
exceed a total of 4 amp maximum current.
• PTC protected outputs are rated @ 1 amp per channel.
• Surge suppression.
Visual Indicators:
• Four (4) power LED indicators.
Enclosure Dimensions:
12”H x 8”W x 6”D
Optional Accessories:
• Video Balun/Combiners:
- HubWayAv - for use with 24VAC cameras.
- HubWayDv - for use with 12VDC cameras.
- HubWayDvi - for use with non-isolated 12VDC cameras.
Specifications:
Additional Models:
HubSat42WP
• HubSat4WP with four (4) HubWayAv
Video Balun/Combiners for 24VAC Cameras.
HubSat43WP
• HubSat4WP with four (4) HubWayDv
Video Balun/Combiners for 12VDC Cameras.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or
moisture. This installation should be made by qualified service personnel and should conform to
all local codes.
Installation Instructions:
HubSat4WP Outdoor Passive UTP Transceiver Hub with Integral Camera Power.
1. Mount unit in desired location. Use hardware supplied and stainless steel fasteners. Mark and predrill holes in the
wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in the wall with the
screw heads protruding. Place the enclosure’s upper keyholes over the two upper screws, level and secure. Mark the
position of the lower two holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the
enclosure’s upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all
screws (Enclosure Dimensions, pg. 8). Secure enclosure to earth ground.
2. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 6).
3. Connect 115VAC 60Hz to the black and white flying leads of open frame transformer. Secure ground
wire (Green) to earth ground (Fig. 4, pg. 6).
4. Select 24VAC or 28VAC power output for each of the Channels 1-4 on HubSat4WP (Fig. 4, pg. 6) with the
corresponding output voltage switches. Select OFF position when servicing or installing individual
cameras (Fig. 1d, pg. 4).
5. Connect the BNC video outputs marked [Video 1-4] on HubSat4WP to the corresponding video inputs on the
head end equipment (DVR) (Fig. 1a, pg. 4).
6. Connect terminals marked [+ Data ---] on HubSat4WP (polarity must be observed) to the RS422/RS485 output
of the head end equipment (DVR) (Fig. 1f, pg. 4). When using fixed cameras disregard this step.
7. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1]
on HubSat4WP (Fig. 1i, pg. 4). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured
cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.