Hub bearing setting – Spicer Hub Service Manual User Manual
Page 19
17
Hub Bearing Setting
•
Torque hub nut to 238-263 lbs. ft. (323-357
N•m).
Note: The hub should be fully rotated several times
in both directions to ensure the hub bearings are
correctly seated.
•
Secure a cord to a wheel stud and wrap cord
around hub, fasten free end to a spring balance.
•
Apply a steady pull to spring balance and note
reading, ignoring the large force initially required
to start rotation.
•
The correct spring balance reading should be
between 8.5 to 12 lbs. (3.8 to 5.4 kg) corre-
sponding to a hub rolling torque of 7-9 lbs. ft. (9-
12 N•m).
•
If spring balance reading is outside limits stated,
adjust hub nut and check again, continuing until
correct figure is obtained.
•
When hub setting is correct, fit lockrings, then
retaining ring.
Note: To align slots in nut with corresponding slots
in axle spindle, do not back off. Continue to tighten
nut until slots are aligned.
AX0139
16
12
10
SPRING
GUAGE
WRAP CORD
AROUND HUB
HS 515 SP, HD 519 SP,
HS716SQ, HD 719 SQ Models
- DSP40 Tandem Axle - Dare to Compare (2 pages)
- Ratio Flex Program Guide (46 pages)
- Italcardano Wing In A Box Product Line (3 pages)
- Vibration Diagnostics (1 page)
- Carrier-To-Housing Joint Leak (6 pages)
- Front Axle Shafts for the Jeep JK (2 pages)
- S400 Helical Gear Retrofit Kit Installation (2 pages)
- Electric Shift Unit (1 page)
- Approved Lubricant (16 pages)
- Tandem Drive Axles Pro-40 Single Reduction and Single Reduction with Differential Lock (102 pages)
- Kingpin Bushing and Seal Installation Instructions (2 pages)
- ROUND BEARING DRIVESHAFT COMPONENTS (11 pages)
- NEW REDESIGNED 40K TANDEM CARRIERS (6 pages)
- HAXL-PNI-34 (1 page)
- Tandem Drive Axles Service Manual S400 (34 pages)
- HAXL-PNI-31 (1 page)
- Single Drive Axles Service Manual: S170, S190, S590 (76 pages)
- PDU Cover & Outer Pinion Support Bearing for 46,000 LB (2 pages)
- 2007 Spicer Driveshafts Service Manual (32 pages)
- DRIVELINE COMPONENTS CATALOG SLIP YOKE ASSEMBLIES (28 pages)
- DualRange Tandem Axles (8 pages)
- S400 Redesigned Power Divider Parts for Service (2 pages)
- Wing Bearing Products U-Joint Identification Chart (1 page)
- 10 Series Driveshafts (86 pages)
- Driveline Components Catalog - Companion Flanges (24 pages)
- Gear & Pinion and Wheel Diff Case Kits Released for D_R170, D_R190 Models (3 pages)
- DST40-(P) (3 pages)
- 22719X, MODEL 44 POWER LOCK DISC AND PLATE KIT (1 page)
- 126155 (1 page)
- 2011 Spicer Bulletin 3; SERVICE_TECHNICAL INFORMATION (1 page)
- Drive Axles Service Manual Single Axles 2-Speed & Double Reduction (34 pages)
- X510-5DSD BILLS OF MATERIAL DODGE CATALOG CORRECTIONS (2 pages)
- Dana “I” Series (2 pages)
- Elimination of PDU Fill Plug On Tandem Drive Axles (2 pages)
- V Drive Components (1 page)
- RST41 (1 page)
- Torsionally Tuned-40 Tandem Drive Axles (2 pages)
- Drive Axles Illustrated Parts List DSS40, DDS40, RSS40, and RDS40 (28 pages)
- Single Drive Axles Service Manual: S140 Series (44 pages)
- DRIVELINE COMPONENTS CATALOG COUPLING SHAFTS - SPL and 10 Series (16 pages)
- Thick Flange Design Carriers (2 pages)
- 2002 Spicer Bulletin; SERVICE_TECHNICAL INFORMATION (1 page)
- Pre-applied Thread Adhesive Compound on Yoke End Nuts (6 pages)
- U-Tube Breather Assembly (2 pages)
- 130542 (1 page)