Yamaha DME64N User Manual
Page 72
Ref
erences
MIDI Data Format
DME64N/DME24N Owner’s Manual
72
Transmit
When the “Parameter Change Tx Switch” is On, appropriate Parameter Change data will be transmitted when a parameter
is edited via the panel controls, as specified by the “MIDI Parameter Change table” and “MIDI Tx Channel” settings.
Refer to “Supplementary Information 1” for cases in which multiple messages are assigned to single parameter.
Refer to “Supplemental Information 2” for information on setting Parameter Data values.
Supplemental Information 1
Messages Transmitted When Multiple Messages are Assigned to the Same Parameter
The DME64N/24N MIDI transmit messages are specified via the “MIDI Control Change Table” and “MIDI Parameter
Change Table.” The “MIDI Control Change Table” and “MIDI Parameter Change Table” can be set up via the DME
Designer application.
Multiple messages can be assigned to a single parameter, but the DME64N/24N will only transmit one of the assigned
messages.
The transmitted messages are as follows:
• If a Control Change message and a Parameter Change message are assigned to the same parameter
→ the Control Change
message will be transmitted.
• If multiple Control Change numbers are assigned to the same parameter
→ the smallest Control Change number
message will be transmitted.
• If multiple Parameter Change numbers are assigned to the same parameter
→ the smallest Parameter Change number
message will be transmitted.
Supplemental Information 2
Setting the Parameter Change Message Parameter Data Values
The Parameter change parameter values are expressed as 32-bit integers with or without parity.
• A parity bit (positive: 0, negative: 1) is added above the most significant value bit (bit 31).
• Fractional parameters will be converted according to the integer table.
• For integers with parity, negative numbers are expressed as the 2’s complement.
Status
F0h (11110000b)
System Exclusive Message
ID No.
43h (01000011b)
Manufacturer's ID No.(YAMAHA)
DEVICE ID.
10h (0001xxxxb)
Rx/Tx Channel (0-15)
GROUP ID.
3Eh (00111110b)
Digital Mixer
MODEL ID.
10h (00010000b)
Device Code (DME)
Parameter
Address
aah (0aaaaaaab)
Parameter Address High
aah (0aaaaaaab)
Parameter Address Low
Parameter
Data Value
ddh (0dddddddb)
data 0
ddh (0dddddddb)
data 1
ddh (0dddddddb)
data 2
ddh (0dddddddb)
data 3
ddh (0dddddddb)
data 4
EOX
F7h (11110111b)
End of Exclusive
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
1
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1 1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
0
0
0
data 0
data 1
data 2
data 3
data 4
0
0
0
0
0
3
E
8
data 0 = 00h
data 1 = 00h
data 2 = 00h
data 3 = 07h
data 4 = 68h
bit0
bit1
bit2
bit3
bit4
bit5
bit6
bit7
bit8
bit9
bit10
bit11
bit12
bit13
bit14
bit15
bit16
bit17
bit18
bit19
bit20
bit21
bit22
bit23
bit24
bit25
bit26
bit27
bit28
bit29
bit30
bit31
sign
0
0
Example
• When value is 1000 (decimal) / 3E8h (hexadecimal):
• When value is 1000 (decimal) / FFFFFC18h (hexadecimal; 2’s complement of 3E8h):
+
-
F
F
F
F
F
C
1
8
data 0 = 1Fh
data 1 = 7Fh
data 2 = 7Fh
data 3 = 78h
data 4 = 18h
Transmitted
Function...
Recognized
Remarks
Basic
Channel
Note
Number : True voice
Velocity
After
Touch
Pitch Bend
Control
Change
Prog
Change : True #
System Exclusive
: Song Pos.
Common : Song Sel.
: Tune
System : Clock
Real Time : Commands
: All Sound Off
Aux : Reset All Cntrls
: Local ON/OFF
Mes- : All Notes OFF
sages: Active Sense
: Reset
Notes:
Mode
Default
Changed
Note ON
Note OFF
Key's
Ch's
0,32
1-31,33-95,102-119
1 - 16
1 - 16
˛
˛
˛
˛
Ш
*1
Ш
*2
Ш
0 - 127 *1
**************
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
not include "DAW controller" command
*1 transmit/receive if program change switch is on.
*2 transmit/receive if control change switch is on.
*3 transmit/receive if parameter change switch is on.
˛
˛
**************
˛
**************
Ø
*3
Mode 1 : OMNI ON , POLY Mode 2 : OMNI ON ,MONO
Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF,MONO
˛
1 - 16
1 - 16
˛
˛
˛
˛
Ш
*1
Ш
*2
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ш
˛
˛
˛
˛
˛
˛
Ш
*3
˛
Ш
: Yes
˛
: No
Default
Messages
Altered
YAMAHA
[Digital Mixing Engine]
Date :31-MAR-2004
Model DME64N/24N MIDI Implementation Chart
Version : 1.0
Memorized
Bank Select
Assignable
Ø
0 - 127 *1
0 - 127
Assignable