beautypg.com

Zoom G7.1ut User Manual

Page 22

background image

MIDI Usage Examples

ZOOM G7.1ut

42

Enable control change send/

receive

The procedure for enabling send/receive of
control change messages is described below.

1.

In play mode, press the [AMP
SELECT/SYSTEM] key.

2.

To enable the G7.1ut to receive
control change messages, turn the
[TYPE] knob to bring up the “MIDI
CTRL Rx” (receive control change)
parameter and turn parameter knob 1
to select the “ON” setting.

3.

To enable the G7.1ut to send control
change messages, turn the [TYPE]
knob to bring up the “MIDI CTRL Tx”
(send control change) parameter and
turn parameter knob 1 to select the
“ON” setting.

4.

When the setting is complete, press
the [EXIT] key to exit the AMP
SELECT/SYSTEM menu.

The indication “Store...?” appears on the display,
to allow you to store the changes.

5.

Press the [STORE/SWAP] key to save
the changes.

The setting is accepted, and the unit returns to
play mode.
In the above condition (while “Store...?” is
shown), only the [STORE/SWAP], [EXIT], and
[PAGE] keys are active. By pressing the [EXIT]
key, you can abort the changes and return to play
mode without saving.

Assigning control change

numbers

You can assign control change numbers to the
expression pedal and keys of the G7.1ut as
follows.

NOTE

Before carrying out the following steps, verify that
the send/receive MIDI channel setting of the
G7.1ut is as required (

p. 37), and that send/

receive of control change messages is enabled (

p. 41).

1.

In play mode, press the [AMP
SELECT/SYSTEM] key.

2.

Turn the [TYPE] knob to bring up the
display for assigning a control change
number.

Operations to which a control change number can
be assigned are listed in the table on the next
page.

For example, to assign a control change number
to the built-in expression pedal, the following
display is used.

¡FRONT

FRONT

AMP Select 1/26

AMP Select 1/26

¡CTRL Rx=ON

CTRL Rx=ON é

MIDI 10/26

MIDI 10/26

¡CTRL Tx=ON

CTRL Tx=ON é

MIDI 11/26

MIDI 11/26

Y[STORE] N[EXIT]

Y[STORE] N[EXIT]

Store...?

Store...?

¡FRONT

FRONT

AMP Select 1/26

AMP Select 1/26

Control change number to be assigned

¡PDL=11

PDL=11

MIDI cc# 13/26

MIDI cc# 13/26

MIDI Usage Examples

ZOOM G7.1ut

43

HINT

The control change number assignment always
applies both for sending and receiving.

3.

Turn parameter knob 1 to specify a
control change number.

4.

Assign control change numbers to
other operations in the same way.

5.

When the setting is complete, press
the [EXIT] key to exit the AMP
SELECT/SYSTEM menu.

The indication “Store...?” appears on the display,
to allow you to store the changes.

6.

Press the [STORE/SWAP] key to save
the changes.

The setting is accepted, and the unit returns to
play mode.
In the above condition (while “Store...?” is
shown), only the [STORE/SWAP], [EXIT], and
[PAGE] keys are active. By pressing the [EXIT]
key, you can abort the changes and return to play

mode without saving.

7.

To send and receive control change
messages, connect the G7.1ut and
the other MIDI device as follows.

Example for sending control change
messages

Control change values sent from the G7.1ut
change as follows.

When the built-in or external expression
pedal is operated

The value of the assigned control change
number is varied continuously over the range
of 0 – 127.

¡PDL=7

PDL=7 é

MIDI cc# 13/26

MIDI cc# 13/26

(2) Control change message is sent

(1) When the expression pedal or
switches and keys at the
G7.1ut are operated...

MIDI OUT
connector

MIDI IN
connector

Display

Control target

Default CC#

CC# setting range

CTRL IN

External expression pedal operation

7

OFF, 1 – 5, 7 – 31, 64 – 95

PDL

Built-in expression pedal operation

11

OFF, 1 – 5, 7 – 31, 64 – 95

COMP

COMP module on/off

64

OFF, 64 – 95

WAH/EFX1

WAH/EFX1 module on/off

65

OFF, 64 – 95

ZNR

ZNR module on/off

66

OFF, 64 – 95

PRE-AMP

PRE-AMP module on/off

67

OFF, 64 – 95

EQUALIZER

EQ module on/off

68

OFF, 64 – 95

MOD/EFX2

MOD/EFX2 module on/off

69

OFF, 64 – 95

DELAY

DELAY module on/off

70

OFF, 64 – 95

REVERB

REVERB module on/off

71

OFF, 64 – 95

MUTE

Mute mode on/off

72

OFF, 64 – 95

BYPASS

Bypass mode on/off

73

OFF, 64 – 95

CH A/B

Pre-amp section channel A/B switching

74

OFF, 64 – 95