York YOCC-YOHC 12-60 - Manual

INSTALLATION &
OWNER’S MANUAL
MINISPLIT FLOOR/CEILING
AIR CONDITIONER
MODELS : YOCC-YOHC 12-60
REQUIRED TOOLS
1. Screw Driver 9. Manifold Guage
2. Hexagonal Wrench 10. Gas Leak Detector
3. Torque Wrench 11. Vacuum Pump
4. Spanner 12. Pipe Clamp
5. Reamer 13. Pipe Cutter
6. Hole Core Drill 14. Flare Tool Set
7. Tape Measure 15. Electrical Circuit Tester
8. Thermometer
EXTENDED PARTS
1. Refrigerant Pipe : See Technical Speci fication
2. Pipe Insulation Material (Polyethylene foam 9 mm thick)
3. Vinyl Tape
4. Putty
• Please read this installation manual carefully before starting installation
of the unit.
• This air conditioning system contains refrigerant under pressure, rotating
parts and electrical connection which may be dangerous and can cause
injury. Installation and maintenance of this air conditioning system should
only be carried out by trained and quali fied personnel.
• After unpacking, please check the unit carefully for possible damage.
• Before undertaking any work on the unit, make sure that the power supply
has been disconnected.
CAUTIONS FOR INSTALLATION
• Do not store or unpack the unit
in a wet area or expose to rain
or water.
It may cause the unit to short circuit and may
result electric shocks or fire.
• Do not install in a place where
flammable gas may leak.
It may cause fire.
• Do not conduct installation in wet
area or in the rain.
It is a high risk to cause the electrical shocks.
• This system is designed for
domestic or residential use only.
If used in certain environments, such as a
manufacturing workplace, the equipment may
not function ef ficiently.
PART LIST
INDOOR UNIT
■ YOCC-YOHC
INSTALLATION ACCESSORIES
E N G L I S H
EN/FR
■ Ceiling & Floor Type
PREPARATION BEFORE INSTALLATION
• Before doing any work, check the interior power supply cord and the main
breaker capacity are suf ficient and the installation area is suf ficient and
complies with the requirements.
• Check that the power supply available agrees with nameplate voltage.
• Electrical work, wiring and cables must be performed in compliance with
national and local wiring codes and standard.
• Do not use the extension cables. In the case extended cables are needed,
use the terminal block.
SELECTION OF THE LOCATION
INDOOR UNIT
OUTDOOR UNIT
INSTALLATION
INSTALLATION SITE
■ To install the air conditioner in the following types of environments,
consult the shop.
• Places with an oily ambient or where steam or soot occurs.
• Salty or corrosive environments such as coastal areas.
• Places where sul fide gas occurs such as hot springs.
The drain from the outdoor unit must be discharged to a place of good drainage.
CONSIDER NUISANCE TO YOUR NEIGHBOURS
FROM NOISES
■ For installation choose a place as described below.
• A place solid enough to bear the weight of the unit and which does not
amplify the operation noise or vibration.
• A place from where the air discharged from
the outdoor unit or the operation noise
will not annoy your neighbours.
ELECTRICAL WORK
• For power supply, be sure to use a separate power circuit dedicated to the air
conditioner.
SYSTEM RELOCATION
• Relocating the air conditioner requires specialized knowledge and skills.
Please consult the shop where you bought the air conditioner if relocation is
necessary for moving or remodelling.
SAFETY PRECAUTIONS
■ Select a place which provides the space around the units as shown in
the diagram below.
To prevent
interference,
place at least
1m away. Inverter-type
fluorescent
lamp. TV
A place with
good
ventilation.
Air Outlet Air Inlet
Radio
035M00003-001
Dimension
(mm)
YOCC-YOHC
12 18 24 30 36 48 60
A 2300 2300 2300 2300 2300 2300 2300
B 2300 2300 2300 2300 2300 2300 2300
C 5 5 5 5 5 5 5
D 120 120 120 120 120 120 120
Dimension
(mm)
YOCC-YOHC
12 18 24 30 36 48 60
A 300 300 300 300 300 300 300
B 2000 2000 2000 2000 2000 2000 2000
C 600 600 600 600 600 600 600
D 300 300 300 300 300 300 300
Description Qty USE
Hook
2
For wall mounting installation
Hanging arm
2
For ceiling installation
Tapping Screw (ST2.9x10-C-H)
2
Remote Controller
1
Frame
Alkalina dry batteries (AM4)
1
Install & Owner’s manual and User’s
guide
& n oi tal lat sn I na m s' re n w O la u e di u G s 'r e s U
2
NAMES AND FUNCTIONS
NOTICE!
The chart based on one model of our product is for reference only, which may be
different from the unit you purchased.
a indoor unit b outdoor unit
c remote controller d air-in
e air flow louver (at air outlet) f connecting pipe
g drain hose h air inlet (with air filter in it)
i installation part j DEF./FAN indicator (For cooling and
heating type, it’s DEF., for cooling only
type, it’s FAN)
k infrared signal receiver l operation lamp
m timer indicator n alarm indicator
o temporary button p air-out
f
c
CC
g
Display Panel
n
m
o
l
k
J
i
a e
d h
p
b
d
p
OPERATION
TIMER
DEF./FAN
ALARM
MANUAL
WALL MOUNTING INSTALLATION
D. Connecting point
of refrigerant pipe
(D. gas side)
Drain point
E. Connecting point
of refrigerant pipe
(E. Liquid side) Hook
Chart 5
1. Fix the hook with tapping screw onto the wall.
(Refer to Chart 6)
2. Hang the indoor unit on the hook.
<6mm
Hook
Chart 6
Tapping screw
Washer
J354-EN.indd 1 J354-EN.indd 1 4/25/07 5:02:52 PM 4/25/07 5:02:52 PM