Tripp Lite HCRK-3 - Manual (Page 11)

11
Storage & Service
Safety & Regulatory Statements
Storage
For short term storage (when charging the Battery Module between shifts), see “Operation” section.
CAUTION!
Even after the Power Supply Module is unplugged, its outlets may still deliver current,
until it is disconnected from the Battery Module and completely turned OFF (deactivated).
Before storing your Power Supply Module, make sure the Battery Module is fully charged. Then, turn the
Power Supply Module completely OFF: unplug the Power Supply Module from the wall outlet, then press
and hold the “Power” button for one second (an alarm will beep once briefly after the interval has passed).
All LEDs and outlets should be OFF. Disconnect the Power Supply Module from the Battery Module. If
you store your Power Supply Module and Battery Module for an extended period of time, recharge the
Battery Module once every month. Follow the connection and recharge procedure in the “Connection /
Start-Up” section. If you leave your Battery Module discharged for an extended period of time, it will
suffer a permanent loss of capacity
Service
Before returning your Power Supply Module or Battery Module for service, follow these steps:
1. Review the installation and operation instructions in this manual to ensure that the service problem does
not originate from a misreading of the instructions.
2. If the problem continues, do not contact or return the unit to the dealer. Instead, call Tripp Lite at
(773) 869-1233. A service technician will ask for the Power Supply Module's and Battery Module's model
numbers, serial numbers and purchase dates and will attempt to correct the problem over the phone.
3. If the problem requires service, the technician will issue you a Returned Material Authorization (RMA)
number, which is required for service. If you require packaging, the technician can arrange to send you
proper packaging. Securely pack the unit to avoid damage during shipping. Do not use Styrofoam beads for
packaging. Any damages (direct, indirect, special, incidental or consequential) to the unit incurred during
shipment to Tripp Lite or an authorized Tripp Lite service center is not covered under warranty. Power
Supply Modules and Battery Supply Modules shipped to Tripp Lite or an authorized Tripp Lite service
center must have transportation charges prepaid. Mark the RMA number on the outside of the package. If
the unit is within the warranty period, enclose a copy of your sales receipt. Return the unit for service using
an insured carrier to the address given to you by the Tripp Lite service technician.
It is the user's responsibility to verify and ensure that Tripp Lite's Medical-Grade, Mobile Power Retrofit Kit is appropriate for use within their
specific application (meeting all safety and regulatory requirements for the application).
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The
series number can be found on the product nameplate label, along with all required approval markings and information. When requesting
compliance information for this product, always refer to the series number. The series number should not be confused with the marking name or
model number of the product.
UL CLASSIFICATION FOR MEDICAL EQUIPMENT: Class I, Type B, Ordinary Equipment, Continuous Operation.
UL60601-1 APPROVAL: The Power Supply Module incorporates a Faraday-shielded isolation transformer that reduces the cumulative leakage
current of all connected equipment to below 300 microamps.
UL1778 APPROVAL: The Power Supply Module described in this manual is UL1778 listed. It meets strict requirements for UPS protection. It
provides battery backup during blackouts, switching between utility power and battery backup power in 2-4 milliseconds.
FCC CLASS A RADIO/TV INTERFERENCE NOTICE: Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy, and if not installed and
used in accordance with the instruction manual, may cause interference to radio communications. Operation of this equipment is likely to cause
harmful interference in which case the user will be required to correct the interference at their own expense. The user must use shielded cables
and connectors with this product. Any changes or modifications to this product not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
200608042 93-2618 Retrofit Kit 3 OM.qxd 9/14/2006 2:01 PM Page 11