Toshiba MA-1595-1 - Manual (Page 100)

10. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11152
10.66 Remote Slip Printer (hardware option) Operation
10-67
10.66 Remote Slip Printer (hardware option) Operation
The Remote Slip Printer TM-U295 (EPSON printer) may be connected to the ECR as an optional device. The
Remote Slip Printer will operate printing if a slip is properly inserted, regardless of the Mode Lock position (except
that no print will occur in the “SET” mode or during program verification in the “X” mode).
1. The remote slip printer will automatically activate printing when the slip has properly been set to the printer
table.
2. The following are selective status programmable relating to the remote slip printer. Ask the store manager
and mark the status selected for your store.
PROGRAM OPTIONS RELATING TO REMOTE SLIP CONTROL
• Remote Slip Print compulsory for any Previous Balance entry in “REG” or “MGR” mode:
Standard: FREE (Not compulsory)
Option: COMPULSORY (applies to any Previous Balance entry whether it is the Manual PB Entry type
or the Customer File (Check Track) Memory type.
• Code No. (Check No.) Entry Before [CHECK NO.] key at Endorsement Print (Refer to ENDORSEMENT
PRINT operation already stated.)
Standard:
FREE (Not compulsory)
Option: COMPULSORY
3. The gap of the slip inlet is usually opened, and the slip may be inserted or withdrawn freely outside a
receipt/journal print sequence.
When a slip is properly set to the remote slip printer and the ECR is operated, the gap will be closed and
printing will be performed. When the sale is finalized and the receipt is issued, the gap of the Remote Slip
Printer will be opened to allow the slip withdrawal. (The gap keeps closed during sale item entries.)
4. The RELEASE key on the TM-U295 may be used to open the closed gap in order to withdraw the slip and
skip unnecessary item print.
5. Printing on the remote slip will be performed alternately with printing on the receipt/journal of the ECR.
6. When the remote slip print is compulsory, the slip printer OFF status or the disconnection of the cable causes
a SLIP OFFLINE error. During the error, the [ITEM CORR] key depression results in that the slip printer
connection check message is displayed. At this time, the [ITEM CORR] key depression again results in that
the slip printer is disconnected, however, the [C] key depression results in that the slip printer remains
connected.
7. When the remote slip print (or endorsement print) is compulsory, the [VALIDATE] or [CHECK NO.] key
depression may cause a SLIP OFFLINE error or SLIP PAPER OUT error. At this time, the compulsion status
is canceled by performing one of the following operations, and you can proceed to the registering operation.
(a) [ITEM CORR] key
→ [ITEM CORR] key
• Depress the [ITEM CORR] key if you want to cancel the compulsion status. At this time, the confirmation
message “COMP CANCEL?” is displayed.
• Depress the [ITEM CORR] key again to perform the cancellation.
• The cancellation continues during a sale transaction.
(b) [ITEM CORR] key
→
[C] key
• When the confirmation message “COMP CANCEL?” is displayed, if you do not want to perform the
cancellation, depress the [C] key.
(c) [C] key
• Depress the [C] key to clear the error message.
After clearing the error, the Validation Print operation or the Endorsement Print operation is possible by
depressing the [VALIDATE] or [CHECK NO.] key.
8. Characters of character codes 1007, 1206, 1207, 1211, 1500 through 1503, 1506 through 1514 such as Ë, Œ,
œ, ∅ , → , ← , ↓ , ↑ , ¹ , ‘ , kg, lb, No, ×, ∇ , ∆ are not printed on the validation slip.