Onkyo AV RECEIVER HT-RC460 - Manual (Page 57)

Advanced Operations
En-57
■ Brightness *1*2*4
` –50 to 0 to +50
With this setting, you can adjust the picture brightness.
“–50” is the darkest. “+50” is the brightest.
■ Contrast *1*2*4
` –50 to 0 to +50
With this setting, you can adjust contrast. “–50” is the
least. “+50” is the greatest.
■ Hue *1*2*4
` –50 to 0 to +50
With this setting, you can adjust the color hue between
“–50” and “+50”.
■ Saturation *1*2*4
` –50 to 0 to +50
With this setting, you can adjust saturation. “–50” is the
weakest color. “+50” is the strongest color.
■ Color Temperature *2*4
` Warm
` Normal
` Cool
With this setting, you can adjust the color temperature.
Note
• “ Picture Adjust ” cannot be used when:
– The NET input selector is selected, or
– “Monitor Out” is set to “Sub”.
*1 This procedure can also be performed on the remote controller
by using the Quick Setup (
➔ page 43 ).
*2 When the “Picture Mode” setting is set to anything other than
“Custom”, this setting cannot be used.
*3 If the “Resolution” setting is set to “4K Upscaling”
(
➔ page 48 ), this setting is fixed at “Off”.
*4 Press CLR if you want to reset to the default value.
*5 If the “Game Mode” setting is set to “On”, this setting is fixed
at “Off”.
*6 When a 3D video source is input, “Wide Mode” is fixed to
“Full”.
Audio Selector
■ Audio Selector
` ARC:
The audio signal from your TV tuner can be sent to
HDMI OUT MAIN of the AV receiver.
*1
With this selection, the TV’s audio can be
automatically selected as a priority among other
assignments.
` HDMI:
This can be selected when HDMI IN has been
assigned as an input source. If both HDMI (HDMI
IN) and digital audio inputs (COAXIAL IN or
OPTICAL IN) have been assigned, HDMI input is
automatically selected as a priority.
` COAXIAL:
This can be selected when COAXIAL IN has been
assigned as an input source. If both coaxial and
HDMI inputs have been assigned, coaxial input is
automatically selected as a priority.
` OPTICAL:
This can be selected when OPTICAL IN has been
assigned as an input source. If both optical and HDMI
inputs have been assigned, optical input is
automatically selected as a priority.
` Analog:
The AV receiver always outputs analog signals.
You can set priorities of audio output when there are both
digital and analog inputs.
Note
• This setting can be made only for an input source that is assigned
to HDMI IN, COAXIAL IN, or OPTICAL IN.
• This setting cannot be used with the NET and USB input
selectors.
*1 You can select “ARC” if you select the TV/CD input selector.
But you cannot if you’ve selected “Off” in the “Audio Return
Channel” setting (
➔ page 61 ).
Setting the Incoming Digital Signal (Fixed
Mode)
■ Fixed Mode
` Off:
The format is detected automatically. If no digital
input signal is present, the corresponding analog
input is used instead.
` PCM:
Only 2-channel PCM format input signals will be
heard. If the input signal is not PCM, the PCM
indicator will flash and noise may also be produced.
` DTS:
Only DTS (but not DTS-HD) format input signals
will be heard. If the input signal is not DTS, the dts
indicator will flash and there will be no sound.
When “HDMI”, “COAXIAL” or “OPTICAL” is selected
in the “Audio Selector” setting, you can then specify the
signal type in “Fixed Mode”.
Normally, the AV receiver detects the signal format
automatically. However, if you experience either of the
following issues when playing PCM or DTS material, you
can manually set the signal format to PCM or DTS.
• If the beginnings of tracks from a PCM source are cut off,
try setting the format to PCM.
• If noise is produced when fast forwarding or reversing a
DTS CD, try setting the format to DTS.
Note
• The setting will be reset to “Off” when you change the setting in
“Audio Selector”.